Cobra CXT 1035R FLT CXT 1035R FLT - Page 11

Operation Mode Functions Introduction Operation Customer Assistance Warranty Tri-Watch Set-up • Your microTALK® radio can be set up to scan three of your favorite BURP • BURP features allows the user to expel water from inside the speaker channels for activity. grille. This is useful if the radio is dropped in the water which may Tri-Watch Button To Program or Edit the Tri-Watch Channels: 1. P ress and hold the TRI-WATCH button from MEM ESC MEM ESC TRI WATCH SCAN TRI WATCH SCAN GMRS Standby mode for two (2) seconds to activate Tri-Watch Setup mode. The TW icon on the display will turn ON. Channel Button The main channel number will flash to RbXecome trapped inVtoThxoe speaker grille and activate BURP: muffle the audio. MEM/ESHCIBuMttoEnD LO1.WPrXess and release the MEM/ESC and Rewind TWbuDtCtoSnsScaat nthe same time. MEM ESC WTARTICH2C.TTChSSeSCABMNurepmtone(s) at maximum level will sound from the internal speaker for 8 seconds. During this CHANNEL CHANNEL VOLUME VOLUME CALL MODETri-Watch Button CHANNEL indicate channel position. 2. P ress Channel Up or Channel Down button to select the desired Tri-Watch channel. 3. Press and release TRI-WATCH button to BURP Icon time, BURP will appear in the display. 3. Hold the radio with the speaker grille down to help BURP PowerthSe awvateerrdrain out. 4. After an 8-second interval, the radio will return to confirm entry. standby. MEM ESC TRI WATCH SCA4N. Repeat steps 2 and 3 to program the remaining CALL additional Tri-Watch memory channel. 5. After programming both Tri-Watch memory MODE channels the radio will immediately engage Tri-Watch mode. Channel Scan • Your microTALK® radio can automatically scan channels. Scan ButtoCnALL To scan channels: 1. Press and release the Scan button until the Scan CHANNEL VOLUME Tri-Watch Button Using Tri-Watch: MEM ESC 1. From GMRS Standby mode, press the TRI-WATCH TRI WATCH SCAN MODEicon and the channel numbers appear on the display. MEM ESC TRI WATCH SCAN button. The TW will appear in the display along with the three channels stored in the Tri-Watch memory. ScaRnXChannels Vox 2. Press and hold the Scan button to begin scanning HI WX channels. TW DCS Scan MEM ESC TRI WATCH SCAN 2. The radio will scan through the three (3) Tri-Watch CTCSS Mem The radio ignores specific privacy VOLUME Channel Button CALL memory channels. 3. A signal on any one (1) of the three (3) channels will stop the scan for 10 seconds to allow you to listen codes while scanning channels. MEM ESC TRI WATCH SCAN BURP Power SaTvhere Scan icon will continue to be displayed when CHANNEL MODE to the traffic on that location. Channel Button scan is on. Your radio will continue to scan all CHANNEL CHANNEL CHANNEL CALL MODETri-Watch Button After the Tri-Watch scan stops to monitor a channel, as long as you do not press any buttons MEM ESC TRI WATCH SCAN within 10 seconds, your radio will automatically resume scanning the Tri-Watch channels CALL 4. Press Channel Up or Channel Down button to MODE resume scanning the Tri-Watch channels or to VOLUME channels and stop if an incoming transmission is detected. Your radio will remain on that channel for CALL 10 seconds. CALL During scanning (while receiving an incoming transmission), MOMDyEOouDEcan choose from the following: a. Press and hold the Talk button to communicate on that channel. Your radio will remain on that channel and return to Standby mode. change the scan direction. b. Press the Channel Up or Channel Down button to resume VOLUME 5. To EXIT the Tri-Watch scan, press the TRI-WATCH scanning channels. button again, and the radio will return to GMRS c. Press and hold the Scan button to return to Standby. Standby mode. 16 Nothing Comes Close to a Cobra® 17 VOLUME UME CHANNEL