Compaq 5500R Service Guide - Page 102

Array Configuration Utility ACU to con the, Run the Array Configuration Utility ACU.

Get Compaq 5500R - ProLiant - 256 MB RAM PDF manuals and user guides
UPC - 743172768186
View all Compaq 5500R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 102 highlights

3-44 Compaq ProLiant 5500 and 5500R Maintenance and Service Guide Table 3-21 ADU Diagnostic Messages continued Message Description Loose cable detected logical drives may be marked FAILED until corrected Controller unable to communicate with one or more physical drives, probably because of a cabling problem. Logical drives may be in a FAILED state until the condition is corrected, preventing access to data on the controller. Mirror data miscompare Data was found at reinitialization in the posted write memory; however, the mirror data compare test failed resulting in data being marked as invalid. Data loss is possible. No configuration for accelerator board The array accelerator board has not been configured. NVRAM configuration present, controller not detected EISA nonvolatile RAM has a configuration for an array controller but there is no board in this slot. Either a board has been removed from the system or a board has been placed in the wrong slot. RIS copies between drives do not match Drives on controller contain copies of RIS which do not match. SCSI Port x Drive ID x has exceeded threshold(s) Monitor and performance threshold for this drive has been violated. SCSI Port x Drive ID x is not stamped for monitoring Drive has not been stamped with monitor and performance features. SCSI Port x Drive ID x RIS copy mismatch SCSI Port x Drive ID x failed - REPLACE (failure message) SCSI Port x Drive ID x firmware needs upgrading Copies of RIS on drive do not match. ADU found drive needs to be replaced. Drive firmware is below recommended version. Recommended Action Check all controller and drive cable connections. Replace the array accelerator board. If the array accelerator board is present, run the Array Configuration Utility (ACU) to configure the board. Place the array controller in the proper slot or run the System Configuration Utility to reconfigure nonvolatile RAM to reflect the removal or new position. Upgrade ADU to the most recent version. Check for the particular threshold that has been violated. Run the Array Configuration Utility (ACU). Changing the configuration and saving should cause ACU to stamp drive with monitor and performance features. To do this without destroying the current configuration, change array accelerator size and save configuration. Change array accelerator back to original size and save again. Drive may need to be replaced. Check for other errors. Replace drive or correct condition that caused error. Run Options ROMPaq to upgrade drive to latest firmware revision. continued For use with Pentium II and Pentium III Xeon processor-based servers only

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
3-44
Compaq ProLiant 5500 and 5500R Maintenance and Service Guide
For use with Pentium II and Pentium III Xeon processor-based servers only
Table 3-21
ADU Diagnostic Messages
continued
Message
Description
Recommended Action
Loose cable
detected -
logical drives
may be marked
FAILED until
corrected
Controller unable to communicate
with one or more physical drives,
probably because of a cabling
problem. Logical drives may be in a
FAILED state until the condition is
corrected, preventing access to data
on the controller.
Check all controller and drive cable
connections.
Mirror data
miscompare
Data was found at reinitialization in
the posted write memory; however,
the mirror data compare test failed
resulting in data being marked as
invalid. Data loss is possible.
Replace the array accelerator board.
No configuration
for accelerator
board
The array accelerator board has not
been configured.
If the array accelerator board is present, run the
Array Configuration Utility (ACU) to configure the
board.
NVRAM
configuration
present,
controller not
detected
EISA nonvolatile RAM has a
configuration for an array controller
but there is no board in this slot.
Either a board has been removed
from the system or a board has been
placed in the wrong slot.
Place the array controller in the proper slot or
run the System Configuration Utility to
reconfigure nonvolatile RAM to reflect the
removal or new position.
RIS copies
between drives
do not match
Drives on controller contain copies of
RIS which do not match.
Upgrade ADU to the most recent version.
SCSI Port x Drive
ID x has
exceeded
threshold(s)
Monitor and performance threshold
for this drive has been violated.
Check for the particular threshold that has been
violated.
SCSI Port x Drive
ID x is not
stamped for
monitoring
Drive has not been stamped with
monitor and performance features.
Run the Array Configuration Utility (ACU).
Changing the configuration and saving should
cause ACU to stamp drive with monitor and
performance features. To do this without
destroying the current configuration, change
array accelerator size and save configuration.
Change array accelerator back to original size
and save again.
SCSI Port x Drive
ID x RIS copy
mismatch
Copies of RIS on drive do not match.
Drive may need to be replaced. Check for other
errors.
SCSI Port x Drive
ID x failed
–
REPLACE
(failure message)
ADU found drive needs to be
replaced.
Replace drive or correct condition that caused
error.
SCSI Port x Drive
ID x firmware
needs upgrading
Drive firmware is below
recommended version.
Run Options ROMPaq to upgrade drive to latest
firmware revision.
continued