Compaq 5500R Service Guide - Page 71

Run the System Configuration, Slot x Drive

Get Compaq 5500R - ProLiant - 256 MB RAM PDF manuals and user guides
UPC - 743172768186
View all Compaq 5500R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

Diagnostic Tools 3-13 Table 3-2 POST Error Messages continued Error Code Audible Beeps L=Long S=Short 1726-Slot x Drive None Array - Array Accelerator Memory Size Change Detected Probable Source of Problem Configuration update. 1727-Slot x Drive Array - New Logical Drive(s) Attachment Detected. If more than 32 logical drives, this message will be followed by: Autoconfiguration failed: Too many logical drives. 1730-Fixed Disk 0 does not support DMA Mode. 1731-Fixed Disk 1 does not support DMA Mode. 1740-Fixed Disk 0 failed Set Block Mode command 1741-Fixed Disk 1 failed Set Block Mode command 1750-Fixed Disk 0 failed Identify command 1751-Fixed Disk 1 failed Identify command 1760-Fixed Disk 0 does not support Block Mode 1761-Fixed Disk 1 does not support Block Mode None Additional drives. None Hard drive error. None Hard drive error. None Hard drive error. None Hard drive error. None Hard drive error. None Hard drive error. None Hard drive error. None Hard drive error. Recommended Action Indicates array accelerator configuration has been updated automatically due to replacement of Array Accelerator (or controller) with one having different memory size. Press F1 to resume. This message indicates that the controller has detected an additional array of drives that was attached when the power was off. The logical drive configuration information has been updated to add the new logical drives. The maximum number of logical drives supported is 32. Additional logical drives will not be added to the configuration. Press F1 to resume. Run the System Configuration Utility and correct. Run the System Configuration Utility and correct. Run the System Configuration Utility and correct. Run the System Configuration Utility and correct. Run the System Configuration Utility and correct. Run the System Configuration Utility and correct. Run the System Configuration Utility and correct. Run the System Configuration Utility and correct. continued For use with Pentium II and Pentium III Xeon processor-based servers only

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
Diagnostic Tools
3-13
For use with Pentium II and Pentium III Xeon processor-based servers only
Table 3-2
POST Error Messages
continued
Error Code
Audible Beeps
L=Long
S=Short
Probable Source of Problem
Recommended Action
1726-Slot x Drive
Array
–
Array
Accelerator Memory
Size Change
Detected
None
Configuration update.
Indicates array accelerator
configuration has been updated
automatically due to
replacement of Array
Accelerator (or controller) with
one having different memory
size. Press
F1
to resume.
1727-Slot x Drive
Array
–
New Logical
Drive(s) Attachment
Detected.
If more than 32
logical drives, this
message will be
followed by: Auto-
configuration failed:
Too many logical
drives.
None
Additional drives.
This message indicates that the
controller has detected an
additional array of drives that
was attached when the power
was off. The logical drive
configuration information has
been updated to add the new
logical drives. The maximum
number of logical drives
supported is 32. Additional
logical drives will not be added
to the configuration. Press
F1
to
resume.
1730-Fixed Disk 0
does not support
DMA Mode.
None
Hard drive error.
Run the System Configuration
Utility and correct.
1731-Fixed Disk 1
does not support
DMA Mode.
None
Hard drive error.
Run the System Configuration
Utility and correct.
1740-Fixed Disk 0
failed Set Block
Mode command
None
Hard drive error.
Run the System Configuration
Utility and correct.
1741-Fixed Disk 1
failed Set Block
Mode command
None
Hard drive error.
Run the System Configuration
Utility and correct.
1750-Fixed Disk 0
failed Identify
command
None
Hard drive error.
Run the System Configuration
Utility and correct.
1751-Fixed Disk 1
failed Identify
command
None
Hard drive error.
Run the System Configuration
Utility and correct.
1760-Fixed Disk 0
does not support
Block Mode
None
Hard drive error.
Run the System Configuration
Utility and correct.
1761-Fixed Disk 1
does not support
Block Mode
None
Hard drive error.
Run the System Configuration
Utility and correct.
continued