Compaq dx1000 Service Reference Guide: Compaq dx1000 Microtower PC - Page 66

Front USB Panel - microtower driver

Get Compaq dx1000 - Microtower PC PDF manuals and user guides View all Compaq dx1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

NOTE: If you are replacing the primary hard drive, use the Recovery Disc Set to restore the operating system, software drivers, and any software applications that were preinstalled on the computer. Front USB Panel 1. Prepare the computer for disassembly (Preparation for Disassembly on page 30). 2. Remove the computer access panel (Computer Access Panel on page 34). 3. Remove the front bezel (Front Bezel on page 35). 4. Disconnect the front USB cable from the yellow system board connector (JAUD1) and the I/O cable from the white system board connector (FUSB1). 5. Stand the unit upright. 6. Remove the silver T15 screw (1) that secures the panel to the chassis. 7. Slide the panel assembly upward (2), and then pull the assembly away from the unit while threading the wires through the hole in the front of the chassis. Figure 6-36 Removing the front USB panel To reinstall the panel, reverse the removal procedure. 60 Chapter 6 Removal and Replacement Procedures Microtower (MT) Chassis

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
NOTE:
If you are replacing the primary hard drive, use the Recovery Disc Set to restore the operating
system, software drivers, and any software applications that were preinstalled on the computer.
Front USB Panel
1.
Prepare the computer for disassembly (
Preparation for Disassembly
on page
30
).
2.
Remove the computer access panel (
Computer Access Panel
on page
34
).
3.
Remove the front bezel (
Front Bezel
on page
35
).
4.
Disconnect the front USB cable from the yellow system board connector (JAUD1) and the I/O cable
from the white system board connector (FUSB1).
5.
Stand the unit upright.
6.
Remove the silver T15 screw
(1)
that secures the panel to the chassis.
7.
Slide the panel assembly upward
(2)
, and then pull the assembly away from the unit while threading
the wires through the hole in the front of the chassis.
Figure 6-36
Removing the front USB panel
To reinstall the panel, reverse the removal procedure.
60
Chapter 6
Removal and Replacement Procedures Microtower (MT) Chassis