Craftsman 30084N Operation Manual - Page 12

Installing Wire Spool And Adjusting Hub Tension, Changing Input Voltage

Get Craftsman 30084N - 180 Amp 220 Volt Digital MIG Welder PDF manuals and user guides
UPC - 055249070420
View all Craftsman 30084N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

2-9. Installing Wire Spool And Adjusting Hub Tension Use compression spring with 8 in (200 mm) spools. Tools Needed: 15/16 in 2-10. Changing Input Voltage 2 3 When a slight force is needed to turn spool, tension is set. ST-072573-B Y Turn Off unit, and disconnect input power. Unit was shipped from factory set for 230 volts. 1 Transformer T1 2 Rear Of Power Switch S1 3 Lead Marked 230 Volt And Fan Motor Lead Disconnect 230 volt lead and fan motor lead from rear of S1. Leave fan motor lead connected to 230 volt lead. 4 Lead Marked 200 Volt Remove cable tie, and slide short piece of sleeving off 200 volt lead, and slide sleeving over end of 230 1 volt and fan motor leads. Fold sleeving over and secure in place. Connect 200 volt lead to S1 where 230 volt lead was removed. Reinstall wrapper. 4 Tools Needed: 3/8, 7/16 in OM-194 199 Page 9 ST-801 580-A

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
OM-194 199 Page 9
2-9.
Installing Wire Spool And Adjusting Hub Tension
ST-072573-B
When a slight force is needed
to turn spool, tension is set.
15/16 in
Use compression spring with
8 in (200 mm) spools.
Tools Needed:
2-10.
Changing Input Voltage
ST-801 580-A
Y
Turn Off unit, and disconnect
input power.
Unit was shipped from factory set
for 230 volts.
1
Transformer T1
2
Rear Of Power Switch S1
3
Lead Marked 230 Volt And
Fan Motor Lead
Disconnect 230 volt lead and fan
motor lead from rear of S1. Leave
fan motor lead connected to 230
volt lead.
4
Lead Marked 200 Volt
Remove cable tie, and slide short
piece of sleeving off 200 volt lead,
and slide sleeving over end of 230
volt and fan motor leads. Fold
sleeving over and secure in place.
Connect 200 volt lead to S1 where
230 volt lead was removed.
Reinstall wrapper.
3/8, 7/16 in
1
Tools Needed:
2
3
4