Craftsman 88830 Operation Manual - Page 10

pin.See

Get Craftsman 88830 - Professional 357 CC 30inch 2 Stage Snow Thrower PDF manuals and user guides View all Craftsman 88830 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

. Makesureall cables are routedto the left of the chutecontrol rod. Line up the hole in the hexend of chute rod with the arrowon the input shaftand insertthe hex end of the rod intothe input shaft belowjoystickon handlepanel.See Figure7. NOTE:Thechute rod will fit snugglyintothe inputshaft. Supportthe rearof the dash panelwith one hand whileinsertingthechute rod with your otherhandto ensurethechute rod is insertedall the way intothe inputshaft. 8. Nowpushthe roundend of chuterod backtowardsthe handle paneluntilthe hole in the rod linesup with the holein the chute control inputclosestto the chutecontrolhead. Insertthe cotter pin.See Figure8. NOTE:The secondholeis usedto achievefurther engagementof the hex end of chute rod intothe inputshaft if requiredand can be usedlaterforadjustmentif thechute doesnot fully rotate.Refertothe Service& Maintenancesectionfor ChuteControlRodadjustments. 9. Finishsecuringchutecontrolhead to chute supportbracketwith wingnut, and clevispin and bow-tiecotter pin removedearlier.Do notovertighten.See Figure9. \, \ y /i _ .J Figure8 Figure7 Figure9 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
.
Makesureall cables are routedto the left of the chutecontrol rod.
Lineuptheholeinthehexendofchuterodwiththearrowonthe
input shaftand insertthe hex end of the rod intothe input shaft
belowjoystickon handlepanel.See Figure7.
NOTE:Thechuterodwillfitsnugglyintotheinputshaft.Supportthe
rearofthedashpanelwithonehandwhileinsertingthechuterodwith
your otherhandto ensurethechute rod is inserted
all the
way
intothe
inputshaft.
8.
Nowpushthe roundend of chuterod backtowardsthe handle
paneluntilthe hole in the rod linesup with the holein the chute
control inputclosestto the chutecontrolhead. Insertthe cotter
pin.SeeFigure8.
NOTE:The secondholeis usedto achievefurtherengagementof
the hex end of chute rod intothe inputshaft if requiredand can be
usedlaterforadjustmentifthechutedoesnotfullyrotate.Refertothe
Service& MaintenancesectionforChuteControlRodadjustments.
9.
Finishsecuringchutecontrolheadtochutesupportbracketwith
wingnut,andclevispinandbow-tiecotterpinremovedearlier.Do
notovertighten.SeeFigure9.
/i
_
.J
Figure8
\
\,
y
..................
Figure7
Figure9
10