D-Link DCS-2120 Product Manual - Page 33

Network - ip reset

Get D-Link DCS-2120 - Wireless Internet Camera PDF manuals and user guides
UPC - 790069289781
View all D-Link DCS-2120 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Section 3 - Configuration Network Reset IP Address at next boot: DCS-2120 will request a new IP address from the DHCP server everytime it restarts. Once the DCS-2120 is configured, this box should be unchecked at all times. If the box has been checked and the connection is lost, run the Installation Wizard to find the camera's IP address. IP address: Necessary for network identification. Subnet mask: Used to determine if the destination is in the same subnet. The default value is "255.255.255.0." Default router: Enter the IP address of the router/gateway. Invalid router settings may cause the failure of transmissions to a different subnet. Primary DNS: Primary domain name server that translates names to IP addresses. Secondary DNS: Secondary domain name server to backup the primary one. Enable UPnP: (Universal Plug & Play) This option allows the computer to find this camera through UPnP, which will show up under "Network Neighborhood" without configuration. UPnP is based on TCP/IP and Internet protocols. UPnP is a networking architecture that provides compatibility among networking equipment, software, and peripherals. The camera is an UPnP enabled device and it will work with other UPnP devices/software. Enable UPnP port forwarding: The camera will add the port forwarding entry into the router automatically when this option is enabled. PPPoE: (Point-to-Point Protocol over Ethernet) Select this option if the camera is directly connected to the Internet through a DSL modem, and the ISP (Internet Service Provider) requires you to use PPPoE for the Internet connection. Input the authentication information from your ISP into these fields. Note: The Internet (WAN) IP Address of the PPPoE will be sent through the email. HTTP Port: Can be set to other than the default port 80. When the administrator changes the HTTP port of the DCS-2120 (which has an IP address of 192.168.0.100) from 80 to 8080, users must type http://192.168.0.100:8080 in the Web browser bar to reach the web configuration page. D-Link DCS-2120 User Manual 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
²²
D-Link DCS-±1±0 User Manual
Section ² - Configuration
Reset IP Address at next boot:
IP address:
Subnet mask:
Default router:
Primary DNS:
Secondary DNS:
Enable UPnP:
Enable UPnP port forwarding:
PPPoE:
HTTP Port:
Network
DCS-2120 will request a new IP address from the DHCP server everytime it restarts. Once the DCS-2120
is configured, this box should be unchecked at all times. If the box has been checked and the connection
is lost, run the Installation Wizard to find the camera’s IP address.
Necessary for network identification.
Used to determine if the destination is in the same subnet. The default value is “255.255.255.0.”
Enter the IP address of the router/gateway. Invalid router settings may cause the failure of transmissions
to a different subnet.
Primary domain name server that translates names to IP addresses.
Secondary domain name server to backup the primary one.
(Universal Plug & Play) This option allows the computer to find this camera through UPnP, which will show
up under “Network Neighborhood” without configuration. UPnP is based on TCP/IP and Internet protocols.
UPnP is a networking architecture that provides compatibility among networking equipment, software, and
peripherals. The camera is an UPnP enabled device and it will work with other UPnP devices/software.
The camera will add the port forwarding entry into the router automatically when this option is enabled.
(Point-to-Point Protocol over Ethernet) Select this option if the camera is directly connected to the Internet
through a DSL modem, and the ISP (Internet Service Provider) requires you to use PPPoE for the Internet
connection. Input the authentication information from your ISP into these fields.
Note:
The Internet (WAN) IP Address of the PPPoE will be sent through the email.
Can be set to other than the default port 80. When the administrator changes the HTTP port of the DCS-2120
(which has an IP address of 192.168.0.100) from 80 to 8080, users must type http://192.168.0.100:8080 in
the Web browser bar to reach the web configuration page.