D-Link DGS-1500-28P User Manual - Page 76

AAA > RADIUS Server, Accounting Port 1 - 65535

Get D-Link DGS-1500-28P PDF manuals and user guides View all D-Link DGS-1500-28P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

5 Configuration D-Link Web Smart Switch User Manual Figure 5.95 - Security > Smart Binding > Black List By giving conditions, desired devices information can be screened out below then click Find to search for a list of the entry: VID: Enter the VLAN ID number of the device. IP Address: Enter the IP Address of the device. MAC Address: Enter the MAC Address of the device. Port: Enter the port number which the device connects. Check a box of Delete column to release an entry from the forbidden list then click Apply to delete an entry from the list. Click Select All to select all entries, or click Clean to select none of the entries. AAA > RADIUS Server The Authentication RADIUS server page allows user to facilitate centralized user administration as well as providing protection against a sniffing, active hacker. Figure 5.96 - AAA > RADIUS Server Index: Choose the desired RADIUS server to configure: 1, 2 or 3. IP Address: Select IPv4 or IPv6 and set the RADIUS server IP address. Authentication Port (1 - 65535): Set the RADIUS authentic server(s) UDP port. The default port is 1812. Accounting Port (1 - 65535): Set the RADIUS account server(s) UDP port. The default port is 1813. Timeout (1 - 255 sec): This field will set the time the Switch will wait for a response of authentication from the user. The user may set a time between 1 and 255 seconds. The default setting is 5 seconds. Retransmit (1 - 255 times): This command will configure the maximum number of times the Switch will accept authentication attempts. Users failing to be authenticated after the set amount of attempts will be denied access to the Switch and will be locked out of further authentication attempts. Command line interface users will have to wait 60 seconds before another authentication attempt. Telnet and web users will be disconnected from the Switch. The user may set the number of attempts from 1 to 255. The default setting is 2. Key: Set the key the same as that of the RADIUS server. Confirm Key: Confirm the shared key is the same as that of the RADIUS server. 71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
5
Configuration
D-Link Web Smart Switch User Manual
71
Figure 5.95 – Security > Smart Binding > Black List
By giving conditions, desired devices information can be screened out below then click
Find
to search for a
list of the entry:
VID:
Enter the VLAN ID number of the device.
IP Address:
Enter the IP Address of the device.
MAC Address:
Enter the MAC Address of the device.
Port:
Enter the port number which the device connects.
Check a box of
Delete
column to release an entry from the forbidden list then click
Apply
to delete an entry
from the list.
Click
Select All
to
select all entries, or click
Clean
to select none of the entries.
AAA > RADIUS Server
The Authentication RADIUS server page allows user to facilitate centralized user administration as well as
providing protection against a sniffing, active hacker.
Figure 5.96 – AAA > RADIUS Server
Index:
Choose the desired RADIUS server to configure: 1, 2 or 3.
IP Address:
Select IPv4 or IPv6 and set the RADIUS server IP address.
Authentication Port (1 - 65535):
Set the RADIUS authentic server(s) UDP port. The default port is 1812.
Accounting Port (1 - 65535):
Set the RADIUS account server(s) UDP port. The default port is 1813.
Timeout (1 – 255 sec):
This field will set the time the Switch will wait for a response of authentication from
the user. The user may set a time between
1
and
255
seconds. The default setting is
5
seconds.
Retransmit (1 – 255 times):
This command will configure the maximum number of times the Switch will
accept authentication attempts. Users failing to be authenticated after the set amount of attempts will be
denied access to the Switch and will be locked out of further authentication attempts. Command line
interface users will have to wait 60 seconds before another authentication attempt. Telnet and web users will
be disconnected from the Switch. The user may set the number of attempts from
1
to
255
. The default
setting is
2
.
Key:
Set the key the same as that of the RADIUS server.
Confirm Key:
Confirm the shared key is the same as that of the RADIUS server.