D-Link DIR-140L User Manual - Page 26

PPTP, Enter the Primary and Secondary DNS Server Addresses Static PPTP only.

Get D-Link DIR-140L PDF manuals and user guides View all D-Link DIR-140L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Section 3 - Configuration PPTP Choose PPTP if your ISP uses a PPTP connection. Your ISP will provide you with a username and password. My Internet Connection Is: Select PPTP from the drop-down menu. Address Mode: Select Static IP if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic. PPTP IP Address: Enter the IP address for your PPTP connection. PPTP Subnet Mask: Enter your PPTP subnet mask. PPTP Gateway IP Address: Enter the Gateway IP address for your PPTP connection. PPTP Server IP Address: Enter the Server IP address for your PPTP connection. User Name: Enter your PPTP user name. Password: Enter your PPTP password and then retype the password in the next box. Reconnect Mode: Select either Always-on, On-Demand, or Manual. Maximum Idle Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Time: Auto-reconnect. DNS Addresses: Enter the Primary and Secondary DNS Server Addresses (Static PPTP only). MTU: Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1492 is the default MTU. MAC Address: The default MAC Address is set to the Internet port's physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. D-Link DIR-140L User Manual 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
22
D-Link DIR-140L User Manual
Section 3 - Configuration
Select
PPTP.
from the drop-down menu.
Select
Static.IP
if your ISP assigned you the IP address, subnet mask, gateway,
and DNS server addresses. In most cases, select
Dynamic
.
Enter the IP address for your PPTP connection.
Enter your PPTP subnet mask.
Enter the Gateway IP address for your PPTP connection.
Enter the Server IP address for your PPTP connection.
Enter your PPTP user name.
Enter your PPTP password and then retype the password in the next box.
Select either
Always-on
,
On-Demand
, or
Manual
.
Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable
Auto-reconnect.
Enter the Primary and Secondary DNS Server Addresses (Static PPTP only).
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1492 is the default
MTU.
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended
that you change the default MAC address unless required by your ISP.
My Internet
Connection Is:
Address Mode:
PPTP IP Address:
PPTP Subnet Mask:
PPTP Gateway IP
Address:
PPTP Server IP
Address:
User Name:
Password:
Reconnect Mode:
Maximum Idle
Time:
DNS Addresses:
MTU:
MAC Address:
PPTP
Choose PPTP if your ISP uses a PPTP connection. Your ISP will provide you with a username and password.