DELPHI TNR800 Installation Guide
DELPHI TNR800 - Navigation System With DVD-ROM Manual
 |
View all DELPHI TNR800 manuals
Add to My Manuals
Save this manual to your list of manuals |
DELPHI TNR800 manual content summary:
- DELPHI TNR800 | Installation Guide - Page 1
If you do, there may be radio and vehicle functions that will not work properly. Items included in the Kit: • Navigation Radio • GPS Antenna • Navigation DVD • Miscellaneous Installation Hardware • Owner's Manual BEFORE YOU BEGIN • Eject all CD's from the factory radio. If you don't, the customer - DELPHI TNR800 | Installation Guide - Page 2
Delphi Touch Screen Navigation Radio Installation Instructions For 2003-2006 Denali and Escalade EXT & ESV & AMP Conversion 3 - 10 Tools needed for the Installation: • Phillips Head Screwdriver • Flat Screwdriver or Prying Device • 7mm, 10mm, Extension and Drive • Bowl for holding screws Estimated - DELPHI TNR800 | Installation Guide - Page 3
the engine (see picture). • You can also look on the under side of the lid for location diagram. Radio/Amp Fuse 2. Disconnect the Battery Negative Cable. WARNING: If you don't, the vehicle could accidentally start and move during this procedure and result in serious personal injury, including death - DELPHI TNR800 | Installation Guide - Page 4
vehicle. • Pull out the radio and disconnect the connections in the rear. IMPORTANT: Some vehicles may have the wires caught on the dash structure behind the radio. This prevents pulling out the radio and disconnecting the plugs. If your vehicle may have to remove part of the weather-stripping from - DELPHI TNR800 | Installation Guide - Page 5
trim or break the vent bezels with the prying tool. • You may want to wrap the tool in cloth to prevent damage to the dash parts. 10. Remove the Passenger Assist Handle. • Reach inside the A/C vent holes and and press the release tabs on both sides of the handle. • Pull the - DELPHI TNR800 | Installation Guide - Page 6
trim to disconnect the ambient light sensor. NOTICE: When lifting up on the dash trim, be careful of the ambient light sensor wiring. There is not much slack in the wiring and it could be torn from the sensor very easily. • Twist the ambient light housing (1/4 twist) to release the sensor from - DELPHI TNR800 | Installation Guide - Page 7
screw slightly forward and to the right (passenger side) of the radio housing area. • Remove the screw from the dash metal support. • Install GPS antenna and install the screw. Screw 13. Route GPS antenna wiring under A/C pipe and to the radio area. For 2003-2006 Denali and Escalade EXT & ESV & ASP - DELPHI TNR800 | Installation Guide - Page 8
. 15. Connect Battery Negative Cable. 16. Install 30A fuse in under-hood fuse box. Radio/Amp Fuse 17. Test Radio. • Make sure parking brake is set. • Start vehicle. • Turn radio On. • Load DVD Navigation Disc. • Once disc checking is complete, press the "NAV" button if the navigation screen doesn - DELPHI TNR800 | Installation Guide - Page 9
Connect ambient light sensor. • Once in position, push in clips located above passenger's airbag. • Engage all remaining clips and make sure dash trim is in position. • Install the metal clip into the upper hole. 20. Test the radio again. 21. Install the dash bezel. • Make sure the parking brake is - DELPHI TNR800 | Installation Guide - Page 10
, then continue. • If something doesn't work correctly, check the connections or something that may have been moved or bumped from the last time you tested. 24. Refer to the Owner's Manual for setting up and operating the Navigation Radio. 25. Finished. NOTES: 10 For 2003-2006 Denali and Escalade - DELPHI TNR800 | Installation Guide - Page 11
the engine (see picture). • You can also look on the under side of the lid for location diagram. Radio/Amp Fuse 2. Disconnect the Battery Negative Cable. WARNING: If you don't, the vehicle could accidentally start and move during this procedure and result in serious personal injury, including death - DELPHI TNR800 | Installation Guide - Page 12
vehicle could move and cause personal injury or damage to the vehicle. • Pull out the radio and disconnect the connections in the rear. • Coaxial Antenna Lead (pull perpendicular to the radio to remove). • XM/DVD the pillar. • You may have to remove part of the weather-stripping from around the door - DELPHI TNR800 | Installation Guide - Page 13
trim or break the vent bezels with the prying tool. • You may want to wrap the tool in cloth to prevent damage to the dash parts. 11. Remove the Passenger Assist Handle. • Reach inside the A/C vent holes and and press the release tabs on both sides of the handle. • Pull the - DELPHI TNR800 | Installation Guide - Page 14
trim to disconnect the ambient light sensor. NOTICE: When lifting up on the dash trim, be careful of the ambient light sensor wiring. There is not much slack in the wiring and it could be torn from the sensor very easily. • Twist the ambient light housing (1/4 twist) to release the sensor from - DELPHI TNR800 | Installation Guide - Page 15
screw slightly forward and to the right (passenger side) of the radio housing area. • Remove the screw from the dash metal support. • Install GPS antenna and install the screw. Screw 14. Route GPS antenna wiring under A/C pipe and to the radio area. For 2003-2006 Non-Class 2 Bose Amp Equipped Chevy - DELPHI TNR800 | Installation Guide - Page 16
Cluster plug and radio plug. NOTICE: Some vehicles may come with this wire installed from the factory (2004 and earlier don't usally have this wire). If you have the wire in position E of the 12-pin radio connector, skip this step. • Using the picture below, connect to the wire in position A4 - DELPHI TNR800 | Installation Guide - Page 17
. 18. Connect Battery Negative Cable. 19. Install 30A fuse in under-hood fuse box. Radio/Amp Fuse 20. Test Radio. • Make sure parking brake is set. • Start vehicle. • Turn radio On. • Load DVD Navigation Disc. • Once disc checking is complete, press the "NAV" button if the navigation screen doesn - DELPHI TNR800 | Installation Guide - Page 18
Connect ambient light sensor. • Once in position, push in clips located above passenger's airbag. • Engage all remaining clips and make sure dash trim is in position. • Install the metal clip into the upper hole. 23. Test the radio again. 24. Install the dash bezel. • Make sure the parking brake is - DELPHI TNR800 | Installation Guide - Page 19
, then continue. • If something doesn't work correctly, check the connections or something that may have been moved or bumped from the last time you tested. 27. Refer to the Owner's Manual for setting up and operating the Navigation Radio. 28. Finished. NOTES: For 2003-2006 Non-Class 2 Bose
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
 |
 |
Delphi Touch Screen Navigation Radio - TNR800
DISCLAIMER – WARNINGS
Purchaser/Installer assumes all responsibility for damages and/or injuries incurred while and after
installing this product.
Delphi is not responsible for damages resulting from kits installed incor-
rectly or individuals not following these instructions correctly.
READ ALL INSTRUCTIONS THROUGHLY BEFORE BEGINNING THE INSTALLATION
Do not attempt to install this radio in any application other than those specified.
If you do,
there may be radio and vehicle functions that will not work properly.
Items included in the Kit:
Navigation Radio
GPS Antenna
Navigation DVD
Miscellaneous Installation Hardware
Owner’s Manual
•
•
•
•
•
BEFORE YOU BEGIN
Eject all CD’s from the factory radio.
If you
don’t, the customer’s CDs may be trapped
in the old unit with no way to remove them.
Set the Parking Brake! If you don’t, the
vehicle could move during this procedure,
causing personal injury or damage to the
vehicle.
Turn the ignition key to the Off Locked:
position.
•
•
•