Dacor DCM24S Use and Care Guide - Page 11

Special, Support, Fig.1-1, Fig.1-2, Fig. 2, support - turntable

Get Dacor DCM24S PDF manuals and user guides View all Dacor DCM24S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Special Note for the Turntable Support and Turntable Read carefully before setting the turntable and turntable support, to turn them smoothly. Improper setting may cause arcing. 1. Place the turntable support to the turntable motor shaft, "Top"side up (Top is engraved on one side). See Fig.l-1 and Fig.l-2. And make sure the center of turntable support is set between three nails of the turntable motor shaft as shown in Fig.2. Fig.1-1 Turntable support Fig.1-2 Fig. 2 Turntable support / Turntable motor shaft The nails of the turntable motor shaft 2. Place the turntable on the turntable support. The turntable should be set as all three rollers of turntable support contact to the flat surface of the turntable. Check the position of the turntable and turntable support, referring to the chart below, and make sure the turntable rotates smoothly. _i_i_i_i_i_i_i_i_i_i_Ii_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_illl Flat surface of the turntable Flat surface of the turntable Back view Side view Rollerof the turntable support Flat surface of the turntable j Roller of the turntable support Out of flat surlace Flat surface of the turntable \ \ Roller of the turntable support

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
Special
Note
for
the
Turntable
Support
and
Turntable
Read carefully
before setting the turntable
and turntable
support,
to turn them smoothly.
Improper
setting may cause arcing.
1. Place the turntable
support to the turntable
motor shaft, "Top"side
up (Top is engraved
on one side). See Fig.l-1
and Fig.l-2.
And make sure the center of turntable
support is set
between three nails of the turntable
motor shaft as shown
in Fig.2.
Fig.1-1
Turntable
support
Fig.1-2
Turntable
motor shaft
Fig. 2
Turntable
support
/
The nails of the turntable
motor shaft
2.
Place the turntable on the turntable support. The turntable
should be set as all three rollers of
turntable
support contact to the flat surface of the turntable. Check the position of the turntable
and turntable support, referring to the chart below, and make sure the turntable
rotates smoothly.
_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_illl
_I
Flat surface
of the turntable
Back
view
Rolleroftheturntablesupport
Side
view
Flat surface
of the
turntable
j
Roller
of the turntable
support
Flat surface
of the
turntable
Out of flat surlace
Flat surface
of the turntable
\
\
Roller of the turntable support