DeLonghi PAC WE130 Owner Manual - Page 14

Self-diagnosis

Get DeLonghi PAC WE130 PDF manuals and user guides View all DeLonghi PAC WE130 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

PROGRAMMING THE TIMER 27 The appliance can be programmed to start up and shut down when required. Programming start up • Press the button. The start-up time and message flash on the remote con- trol display (fig. 27). • Press the or buttons to set the time you want the applian- ce to start up. • When that time is reached, press the OK button to confirm (fig. 28). The message appears on the remote control display and the symbol is displayed on the appliance to indicate that the timer is active. 28 Programming shutdown • Press the OFF button. The shutdown time and message flash on the remote control display (fig. 29). • Press the or buttons to set the time you want the applian- ce to shut down. • When that time is reached, press the OK button to confirm (fig. 30). The message appears on the remote control display and the symbol is displayed on the appliance to indicate that the timer is active. 30 29 SELF-DIAGNOSIS The appliance has a self diagnosis system to identify a number of malfunctions. Error messages are indicated on the control panel display screen. IF...IS DISPLAYED, LOW TEMPERATURE (frost prevention) WHAT SHOULD I DO? The appliance is fitted with a frost protection device to avoid excessive formation of ice. The appliance starts up again automatically when the defrosting process is completed. IF...IS DISPLAYED, HIGH LEVEL (safety tank full) WHAT SHOULD I DO? Empty the internal safety tank, following the instructions in the "End of season operations" section (pg. 17). If this reoccurs, contact your local authorized service center. PROBE FAILURE (sensor damaged) If this is displayed, contact your local authorized service center. CLEAN This message appears after about 500 hours of operation in water mode and indicates that the appliance requires descaling as described in the "descaling" section (pg. 17). After descaling or if the alarm reappears too soon after the last descaling (carried out before the message is displayed), reset the alarm by holding the button down for 10 seconds. 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
14
P
ROGRAMMING THE TIMER
The appliance can be programmed to start up and shut down
when required.
Programming start up
•
Press the
button.
The start-up time and message
flash on the remote con-
trol display (fig. 27).
•
Press the
or
buttons to set the time you want the applian-
ce to start up.
•
When that time is reached, press the
OK
button to confirm
(fig. 28). The message
appears on the remote control
display and the
symbol is displayed on the appliance to
indicate that the timer is active.
Programming shutdown
•
Press the
OFF
button. The shutdown
time and message
flash on the remote control display (fig. 29).
•
Press the
or
buttons to set the time you want the applian-
ce to shut down.
•
When that time is reached, press the
OK
button to confirm
(fig. 30). The message
appears on the remote control
display and the
symbol is displayed on the appliance to
indicate that the timer is active.
27
28
29
30
SELF-DIAGNOSIS
The appliance has a self diagnosis system to identify a number of malfunctions.
Error messages are indicated on the control panel display screen.
I
F
…
IS DISPLAYED
,
WHAT SHOULD I DO
?
L
OW
T
EMPERATURE
(frost prevention)
P
ROBE
F
AILURE
(sensor damaged)
The appliance is fitted with
a frost protection device to
avoid excessive formation
of ice. The appliance starts
up again automatically
when the defrosting pro-
cess is completed.
If this is displayed, contact
your local authorized servi-
ce center.
I
F
…
IS DISPLAYED
,
WHAT SHOULD I DO
?
H
IGH
L
EVEL
(safety tank full)
C
LEAN
Empty the internal safety
tank, following the instruc-
tions in the "End of season
operations" section (pg.
17). If this reoccurs, contact
your local authorized servi-
ce center.
This message appears after
about 500 hours of opera-
tion in water mode and indi-
cates that the appliance
requires descaling as descri-
bed in the "descaling" sec-
tion (pg. 17).
After descaling or if the alarm reappears too soon after
the last descaling (carried out before the message is dis-
played), reset the alarm by holding the
button down
for 10 seconds.