Dell Alienware Aurora R16 Owners Manual - Page 90

System board, Removing the system board

Get Dell Alienware Aurora R16 PDF manuals and user guides View all Dell Alienware Aurora R16 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 90 highlights

Steps 1. Align the captive screws of the VR heat sink with the screw holes on the system board. 2. Tighten the two captive screws that secure the VR heat sink to the system board. 3. Repeat the same procedure for the other VR heat sink. Next steps 1. Install the left-side cover. 2. Follow the procedure in After working inside your computer. System board Removing the system board CAUTION: The information in this removal section is intended for authorized service technicians only. Prerequisites 1. Follow the procedure in Before working inside your computer. NOTE: Your computer's Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup program after you replace the system board. NOTE: Replacing the system board removes any changes that you have made to the BIOS using the BIOS setup program. You must make the appropriate changes again after you replace the system board. NOTE: Before disconnecting the cables from the system board, note the location of the connectors so that you can reconnect the cables correctly after you replace the system board. 2. Remove the left-side cover. 3. Remove the right-side cover. 4. Remove the front bezel. 90

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
Steps
1.
Align the captive screws of the VR heat sink with the screw holes on the system board.
2.
Tighten the two captive screws that secure the VR heat sink to the system board.
3.
Repeat the same procedure for the other VR heat sink.
Next steps
1.
Install the
left-side cover
.
2.
Follow the procedure in
After working inside your computer
.
System board
Removing the system board
CAUTION: The information in this removal section is intended for authorized service technicians only.
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
NOTE:
Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup program
after you replace the system board.
NOTE:
Replacing the system board removes any changes that you have made to the BIOS using the BIOS setup program.
You must make the appropriate changes again after you replace the system board.
NOTE:
Before disconnecting the cables from the system board, note the location of the connectors so that you can
reconnect the cables correctly after you replace the system board.
2.
Remove the
left-side cover
.
3.
Remove the
right-side cover
.
4.
Remove the
front bezel
.
90