Dell Inspiron 1410 Setup Guide - Page 27

Hardware Troubleshooter, NOTICE - Hard Drive SELF MONITORING SYSTEM - motherboard manual

Get Dell Inspiron 1410 PDF manuals and user guides View all Dell Inspiron 1410 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Using Support Tools • Enter system setup and ensure that the boot sequence information is correct (see the Service Manual on the Dell Support website at support.dell.com). No timer tick interrupt - A chip on the system board might be malfunctioning or motherboard failure (see the Service Manual on the Dell Support website at support.dell.com). USB over current error - Disconnect the USB device. Your USB device needs more power for it to function properly. Use an external power source to connect the USB device, or if your device has two USB cables, connect both of them. NOTICE - Hard Drive SELF MONITORING SYSTEM has reported that a parameter has exceeded its normal operating range. Dell recommends that you back up your data regularly. A parameter out of range may or may not indicate a potential hard drive problem - S.M.A.R.T error, possible hard disk drive failure. (see "Contacting Dell" on page 34 for assistance). Hardware Troubleshooter If a device is either not detected during the operating system setup or is detected but incorrectly configured, you can use the Hardware Troubleshooter to resolve the incompatibility. To start the Hardware Troubleshooter: 1. Click Start → Help and Support. 2. Type hardware troubleshooter in the search field and press to start the search. 3. In the search results, select the option that best describes the problem and follow the remaining troubleshooting steps. 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
25
Using Support Tools
Enter system setup and ensure that the boot
•
sequence information is correct (see the
Service Manual
on the Dell Support website
at
support.dell.com
).
No timer tick interrupt
— A chip on the system
board might be malfunctioning or motherboard
failure (see the
Service Manual
on the Dell
Support website at
support.dell.com
).
USB over current error
— Disconnect the USB
device. Your USB device needs more power for
it to function properly. Use an external power
source to connect the USB device, or if your
device has two USB cables, connect both of
them.
NOTICE - Hard Drive SELF MONITORING SYSTEM
has reported that a parameter has exceeded its
normal operating range. Dell recommends that
you back up your data regularly. A parameter
out of range may or may not indicate a potential
hard drive problem
— S.M.A.R.T error, possible
hard disk drive failure. (see “Contacting Dell” on
page 34 for assistance).
Hardware Troubleshooter
If a device is either not detected during
the operating system setup or is detected
but incorrectly configured, you can use the
Hardware Troubleshooter
to resolve the
incompatibility.
To start the Hardware Troubleshooter:
Click
1.
Start
→
Help and Support
.
Type
2.
hardware troubleshooter
in
the search field and press <Enter> to start
the search.
In the search results, select the option that
3.
best describes the problem and follow the
remaining troubleshooting steps.