Dell Inspiron 5594 Service Manual - Page 38

Procedure, Post-requisites, Display assembly, Removing the display assembly

Get Dell Inspiron 5594 PDF manuals and user guides View all Dell Inspiron 5594 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Procedure 1. Place the heat sink on the system board and align the screw holes on the heat sink with the screw holes on the system board. 2. Replace the three (M2x3) screws that secure the heat sink to the system board. NOTE: Applicable only to computers shipped with discrete graphics card. 3. In sequential order (1->2->3->4) as indicated on the heat sink, tighten the captive screws to secure the heat sink to the system board. Post-requisites Replace the base cover. Display assembly Removing the display assembly NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites 1. Remove the base cover. 2. Remove the wireless card. Procedure 1. Open the latch and disconnect the display cable from the system board. 38 Removing and installing components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
Procedure
1.
Place the heat sink on the system board and align the screw holes on the heat sink with the screw holes on the system board.
2.
Replace the three (M2x3) screws that secure the heat sink to the system board.
NOTE:
Applicable only to computers shipped with discrete graphics card.
3.
In sequential order (1->2->3->4) as indicated on the heat sink, tighten the captive screws to secure the heat sink to the system board.
Post-requisites
Replace the
base cover
.
Display assembly
Removing the display assembly
NOTE:
Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in
Before working inside your computer
. After working inside your computer, follow the instructions in
After
working inside your computer
. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance
.
Prerequisites
1.
Remove the
base cover
.
2.
Remove the
wireless card
.
Procedure
1.
Open the latch and disconnect the display cable from the system board.
38
Removing and installing components