Home » Dell Manuals » Desktops » Dell OptiPlex GXi » Manual Viewer

Dell OptiPlex GXi Reference and Installation Guide (.pdf) - Page 105

ISA Configuration Utility Messages, ICU Error Messages

Add to My Manuals
Save this manual to your list of manuals

Page 105 highlights

Appendix B ISA Configuration Utility Messages The ISA Configuration Utility (ICU) and its Configu- ration Manager are capable of identifying problems and alerting you to them. Both utilities can alert you to problems with card configuration as well as problems that prevent proper operation of the utility. This appendix describes each type of message and lists the possible causes and actions you can take to resolve any problems indicated by a message. See the following tables to locate your message and identify any possible corrective actions. ICU Error Messages The ICU can display a variety of error messages while in operation. These messages alert you to problems that prevent the ICU from running correctly, as well as informing you of resource conflicts that prevent the configuration of various cards in your computer. If you receive a message from the ICU, see Table A-1 for suggestions on resolving any problems indicated by the message. Table B-1. Configuration Utility Messages Message Probable Cause Corrective Action Out of memory Memory allocation failed Either of these messages can appear if the system runs out of memory during your operation. Disable any TSR programs or any unneeded device drivers. Another possible solution is to load the dwcfgmg.sys driver into high memory. See "Modifying the Configuration Manager" in Chapter 3 for an example of loading the dwcfgmg.sys driver into high memory using a memory manager. Not enough memory to run the ICU This message appears when you start the ICU if the system does not have enough memory to run the utility. Can't open index file. The ICU cannot find the This file is required index file for its database. for ICU to run. Verify that you are starting the ICU from the directory where it is installed. Make sure to switch to drive A before attempting to start the utility. NOTE: For the full name of an abbreviation or acronym used in this table, see the Glossary in the online System User's Guide. ISA Configuration Utility Messages B-1

Section	Page
Safety Instructions	5
When Using Your Computer System	5
Ergonomic Computing Habits	5
When Working Inside Your Computer	7
Protecting Against Electrostatic Discharge	7
Preface	9
About This Guide	9
Warranty and Return Policy Information	9
Other Documents You May Need	10
Notational Conventions	10
Warnings, Cautions, and Notes	10
Typographical Conventions	10
Introduction	25
System Features	25
Using the Optional Floor Stand	27
Security Cable Slot and Padlock Ring	28
Energy Star Compliance	28
Important Note to Windows 95 Users	29
Accessing Online Documentation	29
Getting Help	30
Using the System Setup Program	31
Entering the System Setup Program	31
System Setup Screens	32
Using the System Setup Program	32
System Setup Categories	34
Time	34
Date	34
Diskette Drive A and Diskette Drive B	34
Drive A Location	34
Drives: Primary and Secondary	34
EIDE Devices	35
If You Have a Problem	35
Base Memory	36
Extended Memory	36
Reserved Memory	36
CPU Speed	36
Num Lock	36
Keyboard Errors	36
System Password	36
Password Status	37
Boot Sequence	37
Setup Password	37
Auto Power On	37
Power Management	37
Saving Monitor Power	38
Saving EIDE Hard-Disk Drive Power	38
Sound	38
NIC	38
Mouse	39
Serial Port	39
Parallel Port	39
Parallel Mode	39
Hard Disk	39
Diskette	39
USB	40
Speaker	40
ECC	40
System Data Categories	40
Using the System Password Feature	40
Assigning a System Password	41
Using Your System Password to Secure Your System	41
Deleting or Changing an Existing System Password	42
Using the Setup Password Feature	42
Assigning a Setup Password	42
Operating With a Setup Password Enabled	43
Deleting or Changing an Existing Setup Password	43
Disabling a Forgotten Password	43
Responding to Error Messages	44
Using the ISA Configuration Utility	45
Quick Start	45
About the ICU	46
ICU Database	46
When to Run the ICU	46
Preparing to Use the ICU	47
Backing Up the ICU Diskette	47
Starting the ICU	47
Accessing Help	47
Making Selections in the ICU	48
Adding a Listed Card	48
Adding an Unlisted Card	50
Modifying a Card	51
Removing a Card	52
Viewing Resources	53
Saving the System Configuration	53
Exiting From the ICU	54
Advanced Features of the ICU	54
Locking and Unlocking Cards	54
Locking and Unlocking All Resources	54
Locking and Unlocking Configuration Resources	55
Modifying the Configuration Manager	55
Using Integrated Devices	57
Video Controller	57
Audio Controller	57
NIC	57
Connecting to a Network	59
Network Cable Requirements	59
Configuring the NIC	59
Client Drivers for Novell NetWare Environments	59
Microsoft Windows 95 Client Driver	59
Microsoft Windows NT 3.5x Client Driver	60
Microsoft Windows for Workgroups Client Driver	60
Microsoft Windows 3.x Client Driver	61
MS-DOS Client Driver	61
OS/2 Client Driver	62
Server Drivers for Novell NetWare Environments	62
Updating NDIS 2.01 Drivers	63
Working Inside Your Computer	65
Before You Begin	65
Safety First—For You and Your Computer	65
Unpacking Your Hardware Option	66
Removing the Computer Cover	66
Replacing the Computer Cover	66
Removing and Replacing the Expansion-Card Cage	67
Removing the Expansion-Card Cage	67
Replacing the Expansion-Card Cage	68
Inside Your Computer	68
Jumpers	68
Switches	69
System Board Labels	72
Installing System Board Options	75
Expansion Cards	76
Expansion Slots	76
Installing an Expansion Card	77
Removing an Expansion Card	78
Adding Memory	78
Performing a Memory Upgrade	79
Installing a DIMM	80
Removing a DIMM	80
Upgrading the Microprocessor	80
Replacing the System Battery	84
Installing Drives	87
Removing and Replacing FrontPanel Inserts	87
Connecting Drives	88
Installing a Drive in the 5.25-Inch Drive Bay	89
Installing an EIDE Hard-Disk Drive	92
Partitioning and Logically Formatting Your EIDE Ha...	94
Installing SCSI Devices	95
SCSI Configuration Guidelines	95
SCSI ID Numbers	95
SCSI Cable and SCSI Termination	95
General Procedure for Installing SCSI Devices	97
Partitioning and Formatting SCSI HardDisk Drives	98
Technical Specifications	99
ISA Configuration Utility Messages	105
ICU Error Messages	105
Configuration Manager Messages	110
Regulatory Notices	115
FCC Notices (U.S. Only)	115
Class A	115
Class B	115
IC Notice (Canada Only)	116
EN 55022 Compliance (Czech Republic Only)	116
CE Notice	117
VCCI Notices (Japan Only)	117
Class 1 Notice	117
Class 2 Notice	117
Korean Regulatory Notice	118
Class A Device	118
Class B Device	118
Polish Center for Testing and Certification Notice...	118
Wymagania Polskiego Centrum BadaÒ i Certyfikacji	118
Pozosta³e instrukcje bez pieczeÒstwa	118
Warranties and Return Policy	121
Limited Three-Year Warranty (U.S. Only)	121
Coverage During Year One	121
Coverage During Years Two and Three	122
General	122
Limited Three-Year Warranty (Canada Only)	122
Coverage During Year One	123
Coverage During Years Two and Three	123
General	123
“Total Satisfaction” Return Policy (U.S. and Canad...	124

Match case Limit results 1 per page

ISA Configuration Utility Messages

Appendix B

ISA Configuration Utility Message

he ISA Configuration Utility

(ICU)

and its Configu-

ration Manager are capable of identifying problems and

alerting you to them.

oth utilities can alert you to prob-

lems with card configuration as well as problems that

prevent proper operation of the utility.

his appendix

describes each type of message and lists the possible

causes and actions you can take to resolve any problems

indicated by a message.

ee the following

tables t

o locate

your message and identify any possible corrective

actions.

CU E

rror Messages

The I

CU c

an display a variety of error messages while in

operation.

hese messages alert you to problems that pre-

vent the I

CU f

rom running correctly, as well as informing

you of resource conflicts that prevent the configuration of

various cards in your computer.

f you receive a message

from the I

CU,

see Table

A-1

for suggestions on resolving

any problems indicated by the message.

Table B-1.

Configuration Utility Message

Message

Probable Cause

Corrective Action

Out of memory

Memory allocation

faile

Either of these messages can

appear if the system runs out

of memory during your

operation.

Disable any TSR programs or any unneeded

device drivers. Another possible solution is to

load the

dwcfgmg.sys

driver into high memory.

See “Modifying the Configuration Manager” in

Chapter 3 for an example of loading the

dwcfgmg.sys

driver into high memory using a

memory manager.

Not enough memory to

run the ICU

This message appears when

you start the I

CU i

f the sys-

tem does not have enough

memory to run the utility.

Can’t open index file.

This file is required

for ICU to run.

The I

CU c

annot find the

index file for its database.

Verify that you are starting the I

CU f

rom the

directory where it is installed.

ake sure to

switch to drive A before attempting to start the

utility.

NOTE:

or the full name of an abbreviation or acronym used in this table, see the Glossary

in the online

System User’s Guide