Home » Dell Manuals » Hubs & Switches » Dell PowerConnect M6348 » Manual Viewer

Dell PowerConnect M6348 User's Guide - Page 533

VLAN Routing, Routing > VLAN Routing

View all Dell PowerConnect M6348 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 533 highlights

Configuring Route Preferences using CLI Command For information about the CLI command that performs this function, see the following chapter in the CLI Reference Guide: • OSPF Commands VLAN Routing You can configure PowerConnect M6220/M6348/M8024 software with some VLANs that support routing. You can also configure the software to allow traffic on a VLAN to be treated as if the VLAN were a router port. When a port is enabled for bridging (default) rather than routing, all normal bridge processing is performed for an inbound packet, which is then associated with a VLAN. Its MAC Destination Address (MAC DA) and VLAN ID are used to search the MAC address table. If routing is enabled for the VLAN, and the MAC DA of an inbound unicast packet is that of the internal bridge-router interface, the packet is routed. An inbound multicast packet is forwarded to all ports in the VLAN, plus the internal bridgerouter interface, if it was received on a routed VLAN. Since a port can be configured to belong to more than one VLAN, VLAN routing might be enabled for all of the VLANs on the port or for only some of the VLANs on the port. VLAN Routing can be used to allow more than one physical port to reside on the same subnet. It could also be used when a VLAN spans multiple physical networks, or when additional segmentation or security is required. This section shows how to configure the PowerConnect M6220/M6348/M8024 software to support VLAN routing. A port can be either a VLAN port or a router port, but not both. However, a VLAN port may be part of a VLAN that is itself a router port. The VLAN Routing menu page contains a link to a web page that displays VLAN Routing parameters and data. To display this page, click Routing > VLAN Routing in the tree view. The following web page is accessible from this menu page: • VLAN Routing Configuration • VLAN Routing Summary Configuring Routing 531

Section	Page
User’s Guide	1
Introduction	17
Switching Features	20
Port-Based Features	22
Spanning Tree Protocol Features	25
IPv6	30
OSPFv3	31
Quality of Service Features	31
Multicast Features	32
CLI Documentation	34
Using Dell™ OpenManage™ Switch Administrator	35
Understanding the Interface	37
Check Boxes	43
Defining Fields	43
Accessing the Switch Through the CLI	43
Console Connection	44
Using the CLI	44
Cable and Port Information	47
Overview	47
Power Connection	50
Hardware Description	51
Overview	51
PowerConnect Front Panel	52
Console (RS-232) Port	55
Configuring Dell™ PowerConnect™	65
Overview	65
Starting the CLI	66
General Configuration Information	68
Baud Rate	68
Booting the Switch	69
Configuration Overview	75
Advanced Configuration	80
Boot Menu Functions	89
Delete Backup Image	93
Activate Backup Image	94
Sample Configuration Process	95
Switch Setup Requirements	95
Configuring System Information	105
Overview	105
Managing Logs	124
Setting the Operational Mode	132
Defining IP Addressing	134
Out of Band Interface	135
Running Cable Diagnostics	145
Managing Device Security	149
Captive Portal	188
Defining SNMP Parameters	209
File Management	231
Defining Advanced Settings	238
Defining Stacking	240
sFlow	247
Industry Standard Discovery Protocol	255
Configuring Switching Information	261
Overview	261
Configuring Ports	287
Configuring Traffic Mirroring	298
Configuring Address Tables	302
Configuring GARP	307
Configuring the Spanning Tree Protocol	310
Configuring VLANs	324
Configuring Voice VLAN	347
Aggregating Ports	349
Managing Multicast Support	355
IGMP Snooping	362
MRouter Status	371
MLD Snooping	372
Configuring the Link Layer Discovery Protocol (LLDP)	379
Creating Link Dependencies	386
Dynamic ARP Inspection	389
DHCP Snooping	397
DHCP Relay	410
Using the Port Aggregator Feature	416
Viewing Statistics and Remote Monitoring	423
Overview	423
Table Views	424
RMON	433
Charts	448
Configuring Routing	453
Overview	453
IP	458
OSPF	465
BOOTP/DHCP Relay Agent	499
IP Helper	502
RIP	509
Router Discovery	520
Router	523
VLAN Routing	533
VRRP	536
Tunnels	546
Loopbacks	551
Configuring IPv6	559
Overview	559
Global Configuration	560
Interface Configuration	561
Interface Summary	564
IPv6 Statistics	565
IPv6 Neighbor Table	570
DHCPv6	571
OSPFv3	586
IPv6 Routes	616
Configuring Quality of Service	623
Quality of Service Overview	623
Configuring Differentiated Services	624
Class of Service	641
Auto VoIP	650
Configuring IP Multicast	653
Overview	653
Multicast Listener Discovery	666
Distance Vector Multicast Routing Protocol	679
Internet Group Management Protocol	688
Protocol Independent Multicast-Dense Mode	703
Protocol Independent Multicast-Sparse Mode	716
Getting Help	731
Dell Enterprise Training and Certification	733
Problems With Your Order	733
Product Information	734
Returning Items for Warranty Repair or Credit	734
Before You Call	734

Match case Limit results 1 per page

Configuring Routing

531

Configuring Route Preferences using CLI Command

For information about the CLI command that performs this function, see the following chapter in the

CLI Reference Guide:

•

OSPF Commands

VLAN Routing

You can configure

PowerConnect M6220/M6348/M8024

software with some VLANs that support routing.

You can also configure the software to allow traffic on a VLAN to be treated as if the VLAN were a router

port.

When a port is enabled for bridging (default) rather than routing, all normal bridge processing is

performed for an inbound packet, which is then associated with a VLAN. Its MAC Destination Address

(MAC DA) and VLAN ID are used to search the MAC address table. If routing is enabled for the VLAN,

and the MAC DA of an inbound unicast packet is that of the internal bridge-router interface, the packet

is routed. An inbound multicast packet is forwarded to all ports in the VLAN, plus the internal bridge-

router interface, if it was received on a routed VLAN.

Since a port can be configured to belong to more than one VLAN, VLAN routing might be enabled for all

of the VLANs on the port or for only some of the VLANs on the port. VLAN Routing can be used to

allow more than one physical port to reside on the same subnet. It could also be used when a VLAN

spans multiple physical networks, or when additional segmentation or security is required. This section

shows how to configure the PowerConnect M6220/M6348/M8024

software to support VLAN routing. A

port can be either a VLAN port or a router port, but not both. However, a VLAN port may be part of a

VLAN that is itself a router port.

The

VLAN Routing

menu page contains a link to a web page that displays VLAN Routing parameters

and data. To display this page, click

Routing > VLAN Routing

in the tree view. The following web page

is accessible from this menu page:

•

VLAN Routing Configuration

•

VLAN Routing Summary