Dell PowerEdge 2200 Service Manual - Page 37

Beep Codes and Error Messages, POST Beep Codes

Get Dell PowerEdge 2200 PDF manuals and user guides View all Dell PowerEdge 2200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Chapter 3 Beep Codes and Error Messages This chapter describes beep codes and system error messages that can occur during POST or, in the case of some failures, during normal system operation. The tables in this chapter list faults that can cause a beep code or system error message to occur and the probable causes of the fault in each case. If a faulty system does not emit beep codes or display system error messages to indicate a failure, you should use the CD-based diagnostics to run the appropriate tests to help isolate the source of the problem. See "Running the System Diagnostics" in Chapter 2. POST Beep Codes If the monitor cannot display error messages during the POST, the system may emit a series of beeps that identifies the problem or that can help you identify a faulty component or assembly. Table 3-1 lists the beep codes that may be generated during the POST. Most beep codes indicate a fatal error that prevents the system from completing the boot routine until the indicated condition is corrected. When the system emits a beep code, record the code and then find it in Table 3-1. If the table does not lead to the source of the problem, run the appropriate tests in the diskette-based diagnostics to assist in troubleshooting the problem. Beep Code 1-2 1-2-2-3 1-3-1-1 Table 3-1. POST Beep Codes Error Probable Causes Invalid expansion-card ROM checksum Improperly seated expansion card or the system needs rebooting. Invalid BIOS ROM check- Corrupted BIOS firmware or sum defective system board. DRAM refresh failure Defective DIMMs or system board. Reseat the DIMMs or replace the system board. Beep Codes and Error Messages 3-1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
Beep Codes and Error Messages
3-1
Chapter 3
Beep Codes and Error Messages
T
his chapter describes beep codes and system error messages that can occur
during POST or, in the case of some failures, during normal system operation.
The tables in this chapter list faults that can cause a beep code or system error
message to occur and the probable causes of the fault in each case.
If a faulty system does not emit beep codes or display system error messages to
indicate a failure, you should use the CD-based diagnostics to run the appropri-
ate tests to help isolate the source of the problem. See “Running the System
Diagnostics” in Chapter 2.
P
OST Beep Codes
If the monitor cannot display error messages during the POST, the system may
emit a series of beeps that identifies the problem or that can help you identify a
faulty component or assembly. Table 3-1 lists the beep codes that may be gener-
ated during the POST. Most beep codes indicate a fatal error that prevents the
system from completing the boot routine until the indicated condition is
corrected.
When the system emits a beep code, record the code and then find it in
Table 3-1. If the table does not lead to the source of the problem, run the appro-
priate tests in the diskette-based diagnostics to assist in troubleshooting the
problem.
Table 3-1.
POST Beep Codes
Beep Code
Error
Probable Causes
1-2
Invalid expansion-card
ROM checksum
Improperly seated expansion
card or the system needs
rebooting.
1-2-2-3
Invalid BIOS ROM check-
sum
Corrupted BIOS firmware or
defective system board.
1-3-1-1
DRAM refresh failure
Defective DIMMs or
system board. Reseat the
DIMMs or replace the
system board.