Dell PowerEdge 4400 Microprocessor Upgrade Installation Guide - Page 12

Installation and Troubleshooting Guide - parts

Get Dell PowerEdge 4400 PDF manuals and user guides View all Dell PowerEdge 4400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

(Rev. 11/3/98) FILE LOCATION: S:\SYSTEMS\SlimFast\ts\ProcUpgrade\028WD\028wdeb0.fm NOTE: If a setup password has been assigned by someone else, contact your network administrator for information on resetting the chassis intrusion detector. 3. Run the Dell Diagnostics to verify that the new microprocessor is operating correctly. See your User's Guide and your Installation and Troubleshooting Guide for additional information on running the Dell Diagnostics and troubleshooting any problems that may occur. ,QVWDOOLQJ DQ 8SJUDGH 0LFURSURFHVVRU LQ 3RZHU(GJH  6\VWHPV This section provides instructions for: ‡ Removing the SEC cartridge and heat sink ‡ Installing the new SEC cartridge and heat sink 5HPRYLQJ WKH 6(& &DUWULGJH DQG +HDW 6LQN 127,&( )ROORZ WKH LQVWUXFWLRQV LQ ´3UHFDXWLRQDU\ 0HDVXUHVµ WR HQVXUH WKDW WKH V\VWHP LV SURSHUO\ VKXW GRZQ DQG GLVFRQQHFWHG IURP DOO SRZHU VRXUFHV (QVXUH WKDW WKH V\VWHP FRQILJXUDWLRQ VFUHHQV DUH UHFRUGHG DV GHVFULEHG LQ ´%HIRUH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
1-8
Microprocessor Upgrade Installation Guide
DELL CONFIDENTIAL - Preliminary
9/11/00
(Rev. 11/3/98) FILE LOCATION:
S:\SYSTEMS\SlimFast\ts\ProcUpgrade\028WD\028wdeb0.fm
NOTE: If a setup password has been assigned by someone else, contact your
network administrator for information on resetting the chassis intrusion detector.
3.
Run the Dell Diagnostics to verify that the new microprocessor is operating
correctly.
See your
User
’
s Guide
and your
Installation and Troubleshooting Guide
for additional
information on running the Dell Diagnostics and troubleshooting any problems that
may occur.
,QVWDOOLQJ±DQ±8SJUDGH±0LFURSURFHVVRU±LQ±
3RZHU(GJH±²³µ´±6\VWHPV
This section provides instructions for:
³
Removing the SEC cartridge and heat sink
³
Installing the new SEC cartridge and heat sink
5HPRYLQJ²WKH²6(&²&DUWULGJH²DQG²+HDW²6LQN
127,&(±²)ROORZ²WKH²LQVWUXFWLRQV²LQ²½3UHFDXWLRQDU\²0HDVXUHVΜ²WR²HQVXUH²WKDW²
WKH²V\VWHP²LV²SURSHUO\²VKXW²GRZQ²DQG²GLVFRQQHFWHG²IURP²DOO²SRZHU²VRXUFHV³²
(QVXUH²WKDW²WKH²V\VWHP²FRQILJXUDWLRQ²VFUHHQV²DUH²UHFRUGHG²DV²GHVFULEHG²LQ²
½%HIRUH²<RX²%HJLQ³Μ²
1.
Turn off the system, including any attached peripherals, and disconnect the power
cable from the electrical outlet.
2.
Open the system cover.
See your system
Installation and Troubleshooting Guide
for specific instructions,
if needed.
3.
Remove the air blower, if present (see Figure 1-4).
a.
Unplug the Y-shaped air blower power cable from the interposer board.
b.
Position your right thumb on the outside of the power supply enclosure
beside the narrower front part of the air blower.
c.
Push firmly on the power supply enclosure to move it slightly away from the
air blower and allow extra clearance to remove the air blower.
d.
With your left hand, pull the front of the air blower upward and away from
the power supplies to unseat it. You should hear it unsnap.
By pulling the air blower slightly away from the power supplies, you avoid the
need to use excessive force to clear the power supply enclosure.
e.
Slide the air blower slightly up and toward the front of the chassis until the
metal tab at the back right of the air blower slides out of the small slot at the
top back of the chassis.