Dell PowerEdge 4400 Microprocessor Upgrade Installation Guide - Page 16

Turn off the system, including any attached peripherals, and disconnect the AC - speed

Get Dell PowerEdge 4400 PDF manuals and user guides View all Dell PowerEdge 4400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

(Rev. 11/3/98) FILE LOCATION: S:\SYSTEMS\SlimFast\ts\ProcUpgrade\028WD\028wdeb0.fm 8SJUDGLQJ WKH 0LFURSURFHVVRU RU ,QVWDOOLQJ D 6HFRQGDU\ 0LFURSURFHVVRU LQ 3RZHU(GJH  6\VWHPV Each microprocessor is contained within an SEC cartridge and heat sink assembly. The system board has two guide-bracket assemblies, which hold the SEC cartridge and heat sink assemblies. If your system has only one microprocessor, the secondary guide-bracket assembly must contain a terminator card. If you add a second microprocessor to the system, its maximum speed need not match that of the primary microprocessor, but the internal operating speed of the faster microprocessor will be reduced to match the speed of the slower microprocessor. 127,&( ,I \RX DUH XSJUDGLQJ D V\VWHP E\ LQVWDOOLQJ D VHFRQGDU\ PLFURSUR FHVVRU \RX PXVW RUGHU DQ XSJUDGH NLW IURP 'HOO 7KH XSJUDGH NLW IURP 'HOO FRQWDLQV WKH FRUUHFW YHUVLRQ RI WKH PLFURSURFHVVRU IRU XVH DV D VHFRQGDU\ PLFURSURFHVVRU 5HPRYLQJ D 7HUPLQDWRU &DUG To remove a terminator card, perform the following steps. :$51,1* %HIRUH \RX SHUIRUP WKLV SURFHGXUH \RX PXVW WXUQ RII WKH FRP SXWHU DQG GLVFRQQHFW LW IURP LWV $& SRZHU VRXUFH )RU PRUH LQIRUPDWLRQ VHH 6DIHW\ )LUVW³)RU

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
1-12
Microprocessor Upgrade Installation Guide
DELL CONFIDENTIAL - Preliminary
9/11/00
(Rev. 11/3/98) FILE LOCATION:
S:\SYSTEMS\SlimFast\ts\ProcUpgrade\028WD\028wdeb0.fm
8SJUDGLQJ±WKH±0LFURSURFHVVRU±RU±
,QVWDOOLQJ±D±6HFRQGDU\±0LFURSURFHVVRU±LQ±
3RZHU(GJH±³³´´±6\VWHPV
Each microprocessor is contained within an SEC cartridge and heat sink assembly.
The system board has two guide-bracket assemblies, which hold the SEC cartridge
and heat sink assemblies. If your system has only one microprocessor, the secondary
guide-bracket assembly must contain a terminator card.
If you add a second microprocessor to the system, its maximum speed need not
match that of the primary microprocessor, but the internal operating speed of the
faster microprocessor will be reduced to match the speed of the slower
microprocessor.
127,&(±²,I²\RX²DUH²XSJUDGLQJ²D²V\VWHP²E\²LQVWDOOLQJ²D²VHFRQGDU\²PLFURSURµ
FHVVRU´²\RX²PXVW²RUGHU²DQ²XSJUDGH²NLW²IURP²'HOO³²7KH²XSJUDGH²NLW²IURP²'HOO²
FRQWDLQV²WKH²FRUUHFW²YHUVLRQ²RI²WKH²PLFURSURFHVVRU²IRU²XVH²DV²D²VHFRQGDU\²
PLFURSURFHVVRU³
5HPRYLQJ²D²7HUPLQDWRU²&DUG
To remove a terminator card, perform the following steps.
:$51,1*±²%HIRUH²\RX²SHUIRUP²WKLV²SURFHGXUH´²\RX²PXVW²WXUQ²RII²WKH²FRPµ
SXWHU²DQG²GLVFRQQHFW²LW²IURP²LWV²$&²SRZHU²VRXUFH³²)RU²PRUH²LQIRUPDWLRQ´²VHH²
¾6DIHW\²)LUVW¿)RU²<RX²DQG²<RXU²&RPSXWHU¾²LQ²WKH²
'HOO±3RZHU(GJH±6\VWHPV±
,QVWDOODWLRQ±DQG±7URXEOHVKRRWLQJ±*XLGH
³
1.
Turn off the system, including any attached peripherals, and disconnect the AC
power cable from its power source.
127,&(±²6HH²¾3URWHFWLQJ²$JDLQVW²(OHFWURVWDWLF²'LVFKDUJH¾²LQ²WKH²VDIHW\²
LQVWUXFWLRQV²DW²WKH²IURQW²RI²\RXU²V\VWHP²
,QVWDOODWLRQ±DQG±7URXEOHVKRRWLQJ±
*XLGH
³
2.
Remove the computer cover.
3.
Remove the cooling shroud.
4.
Lift the latches on each end of the guide-bracket assembly (see Figure 1-7).