Dell PowerEdge 4400 Microprocessor Upgrade Installation Guide - Page 8

HDW 6LQN - specifications

Get Dell PowerEdge 4400 PDF manuals and user guides View all Dell PowerEdge 4400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

(Rev. 11/3/98) FILE LOCATION: S:\SYSTEMS\SlimFast\ts\ProcUpgrade\028WD\028wdeb0.fm ,QVWDOOLQJ DQ 8SJUDGH 0LFURSURFHVVRU LQ 3RZHU(GJH  6\VWHPV This section provides instructions for: ‡ Removing the cooling shroud, single-edge contact (SEC) cartridge, and heat sink ‡ Installing the new SEC cartridge and heat sink and replacing the cooling shroud ‡ Reassembling and checking the system 5HPRYLQJ WKH &RROLQJ 6KURXG 6(& &DUWULGJH DQG +HDW 6LQN 127,&( )ROORZ WKH LQVWUXFWLRQV LQ ´3UHFDXWLRQDU\ 0HDVXUHVµ WR HQVXUH WKDW WKH V\VWHP LV SURSHUO\ VKXW GRZQ DQG GLVFRQQHFWHG IURP DOO SRZHU VRXUFHV (QVXUH WKDW WKH V\VWHP FRQILJXUDWLRQ VFUHHQV DUH UHFRUGHG DV GHVFULEHG LQ ´%HIRUH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
1-4
Microprocessor Upgrade Installation Guide
DELL CONFIDENTIAL - Preliminary
9/11/00
(Rev. 11/3/98) FILE LOCATION:
S:\SYSTEMS\SlimFast\ts\ProcUpgrade\028WD\028wdeb0.fm
,QVWDOOLQJ±DQ±8SJUDGH±0LFURSURFHVVRU±LQ±
3RZHU(GJH±²³´´±6\VWHPV
This section provides instructions for:
³
Removing the cooling shroud, single-edge contact (SEC) cartridge, and heat sink
³
Installing the new SEC cartridge and heat sink and replacing the cooling shroud
³
Reassembling and checking the system
5HPRYLQJ²WKH²&RROLQJ²6KURXG±²6(&²&DUWULGJH±²DQG²
+HDW 6LQN
127,&(±²)ROORZ²WKH²LQVWUXFWLRQV²LQ²½3UHFDXWLRQDU\²0HDVXUHVΜ²WR²HQVXUH²WKDW²
WKH²V\VWHP²LV²SURSHUO\²VKXW²GRZQ²DQG²GLVFRQQHFWHG²IURP²DOO²SRZHU²VRXUFHV³²
(QVXUH²WKDW²WKH²V\VWHP²FRQILJXUDWLRQ²VFUHHQV²DUH²UHFRUGHG²DV²GHVFULEHG²LQ²
½%HIRUH²<RX²%HJLQ³Μ²
1.
Turn off the system, including any attached peripherals, and disconnect the power
cable from the electrical outlet.
2.
Remove the right-side system cover and bezel.
See your system
Installation and Troubleshooting Guide
for specific instructions,
if needed.
3.
Remove the cooling shroud as follows:
a.
Unscrew and remove the two retention pins (see Figure 1-1).
b.
Remove the shroud by lifting the end of the shroud closest to the micropro-
cessor(s) until the opposite end of the shroud disengages from the cooling
fan on the system
’
s back panel (see Figure 1-1).