Dell PowerEdge 4400 Microprocessor Upgrade Installation Guide - Page 18

power cable from its power source.

Get Dell PowerEdge 4400 PDF manuals and user guides View all Dell PowerEdge 4400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

(Rev. 11/3/98) FILE LOCATION: S:\SYSTEMS\SlimFast\ts\ProcUpgrade\028WD\028wdeb0.fm 5. Pivot the retention clips away from the guide-bracket assembly. 6. Slide the terminator card out of the guide-bracket assembly. ,QVWDOOLQJ D 7HUPLQDWRU &DUG To install a terminator card in the guide-bracket assembly, perform the following steps: 1. Slide the terminator card into the guide-bracket assembly until the edge connec- tor on the terminator card is firmly seated in the connector on the system board. 2. Place the retention clips on each end of the guide bracket in the notches on the ends of the guide bracket, and then close the two latches to secure the terminator card in the bracket. 5HPRYLQJ WKH 6(& &DUWULGJH DQG +HDW 6LQN $VVHPEO\ To remove the SEC cartridge and heat sink assembly, perform the following steps. &$87,21 7KH 6(& FDUWULGJH DQG KHDW VLQN DVVHPEO\ FDQ JHW H[WUHPHO\ KRW GXULQJ V\VWHP RSHUDWLRQ %H VXUH WKDW WKH DVVHPEO\ KDV KDG VXIILFLHQW WLPH WR FRRO EHIRUH \RX WRXFK LW &$87,21 :KHQ KDQGOLQJ WKH 6(& FDUWULGJH DQG KHDW VLQN DVVHPEO\ WDNH FDUH WR DYRLG VKDUS HGJHV RQ WKH KHDW VLQN :$51,1* %HIRUH \RX SHUIRUP WKLV SURFHGXUH \RX PXVW WXUQ RII WKH FRP SXWHU DQG GLVFRQQHFW LW IURP LWV $& SRZHU VRXUFH )RU PRUH LQIRUPDWLRQ VHH 6DIHW\ )LUVW³)RU

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
1-14
Microprocessor Upgrade Installation Guide
DELL CONFIDENTIAL - Preliminary
9/11/00
(Rev. 11/3/98) FILE LOCATION:
S:\SYSTEMS\SlimFast\ts\ProcUpgrade\028WD\028wdeb0.fm
5.
Pivot the retention clips away from the guide-bracket assembly.
6.
Slide the terminator card out of the guide-bracket assembly.
,QVWDOOLQJ²D²7HUPLQDWRU²&DUG
To install a terminator card in the guide-bracket assembly, perform the following steps:
1.
Slide the terminator card into the guide-bracket assembly until the edge connec-
tor on the terminator card is firmly seated in the connector on the system board.
2.
Place the retention clips on each end of the guide bracket in the notches on the
ends of the guide bracket, and then close the two latches to secure the termina-
tor card in the bracket.
5HPRYLQJ²WKH²6(&²&DUWULGJH²DQG²+HDW²6LQN²$VVHPEO\
To remove the SEC cartridge and heat sink assembly, perform the following steps.
&$87,21±²7KH²6(&²FDUWULGJH²DQG²KHDW²VLQN²DVVHPEO\²FDQ²JHW²H[WUHPHO\²KRW²
GXULQJ²V\VWHP²RSHUDWLRQ³²%H²VXUH²WKDW²WKH²DVVHPEO\²KDV²KDG²VXIILFLHQW²WLPH²
WR²FRRO²EHIRUH²\RX²WRXFK²LW³
&$87,21±²:KHQ²KDQGOLQJ²WKH²6(&²FDUWULGJH²DQG²KHDW²VLQN²DVVHPEO\´²WDNH²
FDUH²WR²DYRLG²VKDUS²HGJHV²RQ²WKH²KHDW²VLQN³
:$51,1*±²%HIRUH²\RX²SHUIRUP²WKLV²SURFHGXUH´²\RX²PXVW²WXUQ²RII²WKH²FRPµ
SXWHU²DQG²GLVFRQQHFW²LW²IURP²LWV²$&²SRZHU²VRXUFH³²)RU²PRUH²LQIRUPDWLRQ´²VHH²
¾6DIHW\²)LUVW¿)RU²<RX²DQG²<RXU²&RPSXWHU¾²LQ²WKH²
'HOO±3RZHU(GJH±6\VWHPV±
,QVWDOODWLRQ±DQG±7URXEOHVKRRWLQJ±*XLGH
³
1.
Turn off the system, including any attached peripherals, and disconnect the AC
power cable from its power source.
127,&(±²6HH²¾3URWHFWLQJ²$JDLQVW²(OHFWURVWDWLF²'LVFKDUJH¾²LQ²WKH²VDIHW\²
LQVWUXFWLRQV²DW²WKH²IURQW²RI²\RXU²V\VWHP²
,QVWDOODWLRQ±DQG±7URXEOHVKRRWLQJ±
*XLGH
³
2.
Remove the computer cover.
3.
Remove the cooling shroud.
4.
Lift the latches on each end of the guide-bracket assembly.
5.
Pivot the retention clips away from the guide-bracket assembly.
6.
Slide the SEC cartridge and heat sink assembly out of the guide-bracket
assembly.