Dell PowerEdge 860 Hardware Owner's Manual (PDF) - Page 20

See Troubleshooting a USB Device on, Troubleshooting a Hard Drive - replacement

Page 20 highlights

Table 1-4. System Messages (continued) Message Causes Corrective Actions Primary drive 0/1 failure Faulty drive. INT13 call failure from the drive. Ensure that the hard drive cables are properly connected. See "Troubleshooting a Hard Drive" on page 90. Read fault The operating system cannot read Requested sector not found from the diskette or hard drive, the system could not find a particular sector on the disk, or the requested sector is defective. Replace the diskette. Ensure that the diskette and hard-drive cables are properly connected. See "Troubleshooting a USB Device" on page 83, "Troubleshooting a Hard Drive" on page 90, or "Troubleshooting a Hard Drive" on page 90 for the appropriate drive(s) installed in your system. Remote Configuration update attempt failed System could not implement Remote Retry Remote Configuration. Configuration request. ROM bad checksum = address Faulty or improperly installed expansion card. Remove and reseat the expansion cards. See "Troubleshooting Expansion Cards" on page 91. SATA port 0/1 hard disk Faulty drive. Parameters failure. drive configuration error Ensure that the hard drive cables are properly connected. See "Troubleshooting a Hard Drive" on page 90. SATA port 0/1 hard disk drive failure SATA port 0/1 hard disk drive auto-sensing error Faulty drive. INT13 call failure from the drive. Ensure that the hard drive cables are properly connected. See "Troubleshooting a Hard Drive" on page 90. SATA Port 0/1 hard disk not SATA Port0/1 set as Auto, no disk found installed. Run the System Setup program to correct the settings. See "Using the System Setup Program" on page 29. Sector not found Seek error Seek operation failed Faulty diskette or hard drive. See "Troubleshooting a USB Device" on page 83, "Troubleshooting a Hard Drive" on page 90, or "Troubleshooting a Hard Drive" on page 90 for the appropriate drive installed in your system. Shutdown failure Shutdown test failure. Ensure that all memory modules are properly installed. See "Troubleshooting System Memory" on page 88. If the problem persists, see "Getting Help" on page 103. 20 About Your System

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140

20
About Your System
Primary drive 0/1 failure
Faulty drive. INT13 call failure from
the drive.
Ensure that the hard drive cables are
properly connected. See
"Troubleshooting a Hard Drive" on
page 90.
Read fault
Requested sector not found
The operating system cannot read
from the diskette or hard drive, the
system could not find a particular
sector on the disk, or the requested
sector is defective.
Replace the diskette. Ensure that the
diskette and hard-drive cables are
properly connected. See
"Troubleshooting a USB Device" on
page 83, "Troubleshooting a Hard Drive"
on page 90, or "Troubleshooting a Hard
Drive" on page 90 for the appropriate
drive(s) installed in your system.
Remote Configuration
update attempt failed
System could not implement Remote
Configuration request.
Retry Remote Configuration.
ROM bad checksum =
address
Faulty or improperly installed
expansion card.
Remove and reseat the expansion cards.
See "Troubleshooting Expansion Cards"
on page 91.
SATA port 0/1 hard disk
drive configuration error
Faulty drive. Parameters failure.
Ensure that the hard drive cables are
properly connected. See
"Troubleshooting a Hard Drive" on
page 90.
SATA port 0/1 hard disk
drive failure
SATA port 0/1 hard disk
drive auto-sensing error
Faulty drive. INT13 call failure from
the drive.
Ensure that the hard drive cables are
properly connected. See
"Troubleshooting a Hard Drive" on
page 90.
SATA Port 0/1 hard disk not
found
SATA Port0/1 set as Auto, no disk
installed.
Run the System Setup program to
correct the settings. See "Using the
System Setup Program" on page 29.
Sector not found
Seek error
Seek operation failed
Faulty diskette or hard drive.
See "Troubleshooting a USB Device" on
page 83, "Troubleshooting a Hard Drive"
on page 90, or "Troubleshooting a Hard
Drive" on page 90 for the appropriate
drive installed in your system.
Shutdown failure
Shutdown test failure.
Ensure that all memory modules are
properly installed. See "Troubleshooting
System Memory" on page 88. If the
problem persists, see "Getting Help" on
page 103.
Table 1-4.
System Messages
(continued)
Message
Causes
Corrective Actions