Dell PowerEdge C8000 Dell PowerEdge C8220 Hardware Owner's Manual - Page 186

See Supported DIMM Configuration on See Main Menu

Get Dell PowerEdge C8000 PDF manuals and user guides View all Dell PowerEdge C8000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 186 highlights

2 After 10 seconds, turn on the sled and attached peripherals and note the messages on the screen. Go to step 13 if an error message appears indicating a fault with a specific memory module. 3 Enter the System Setup program and check the system memory settings. See "Main Menu" on page 52. Make any changes to the memory settings, if needed. If the memory settings match the installed memory but a problem is still indicated, go to step 13. 4 Turn off the sled and attached peripherals. 5 Remove the sled from the enclosure. See "Removing a Sled" on page 129. 6 Remove the cooling shroud. See "Removing the Cooling Shroud" on page 135. 7 Check the memory channels and ensure that they are populated correctly. See "Supported DIMM Configuration" on page 144. 8 Reseat the memory modules in their sockets. See "Removing Memory Modules" on page 146 and "Installing Memory Modules" on page 147. 9 Replace the cooling shroud. See "Installing the Cooling Shroud" on page 136. 10 Reinstall the sled into the enclosure. See "Installing a Sled" on page 130. 11 Turn on the sled and attached peripherals. 12 Enter the System Setup program and check the system memory settings. See "Main Menu" on page 52. If the problem is not resolved, proceed with the next step. 13 Turn off the sled and attached peripherals. 14 Remove the sled from the enclosure. See "Removing a Sled" on page 129. 15 Remove the cooling shroud. See "Removing the Cooling Shroud" on page 135. 16 If a diagnostic test or error message indicates a specific memory module as faulty, swap or replace the module. 186 Troubleshooting

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
186
Troubleshooting
2
After 10 seconds, turn on the sled and attached peripherals and note the
messages on the screen.
Go to step 13 if an error message appears indicating a fault with a specific
memory module.
3
Enter the System Setup program and check the system memory settings.
See "Main Menu" on page 52. Make any changes to the memory settings, if
needed.
If the memory settings match the installed memory but a problem is still
indicated, go to step 13.
4
Turn off the sled and attached peripherals.
5
Remove the sled from the enclosure. See "Removing a Sled" on page 129.
6
Remove the cooling shroud. See "Removing the Cooling Shroud" on
page 135.
7
Check the memory channels and ensure that they are populated correctly.
See "Supported DIMM Configuration" on page 144.
8
Reseat the memory modules in their sockets. See "Removing Memory
Modules" on page 146 and "Installing Memory Modules" on page 147.
9
Replace the cooling shroud. See "Installing the Cooling Shroud" on
page 136.
10
Reinstall the sled into the enclosure. See "Installing a Sled" on page 130.
11
Turn on the sled and attached peripherals.
12
Enter the System Setup program and check the system memory settings.
See "Main Menu" on page 52.
If the problem is not resolved, proceed with the next step.
13
Turn off the sled and attached peripherals.
14
Remove the sled from the enclosure. See "Removing a Sled" on page 129.
15
Remove the cooling shroud. See "Removing the Cooling Shroud" on
page 135.
16
If a diagnostic test or error message indicates a specific memory module as
faulty, swap or replace the module.