Dell PowerEdge R6525 EMC Technical Specifications - Page 11

Table 7. Rear view of the system

Get Dell PowerEdge R6525 PDF manuals and user guides View all Dell PowerEdge R6525 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Table 7. Rear view of the system Item Ports, panels, or slots Icon 1 Power supply unit (PSU 1) 2 PCIe expansion card riser N/A (slot 1) 3 PCIe expansion card riser N/A (slot 2) 4 USB 2.0 port (1) Description For more information about the PSU configurations, see the Technical Specifications section. The expansion card riser enables you to connect PCI Express expansion cards. For more information about the expansion cards that are supported on your system, see Technical Specifications section. The expansion card riser enables you to connect PCI Express expansion cards. For more information about the expansion cards that are supported on your system, see Technical Specifications section. This port is USB 2.0-compliant. 5 PCIe expansion card riser N/A (slot 3) 6 Power supply unit (PSU 2) 7 VGA port 8 USB 3.0 port (1) The expansion card riser enables you to connect PCI Express expansion cards. For more information about the expansion cards that are supported on your system, see Technical Specifications section. For more information about the PSU configurations, see the Technical Specifications section. Enables you to connect a display device to the system. For more information, see the Technical Specifications section. This port is USB 3.0-compliant. 9 iDRAC dedicated port 10 System identification button 11 OCP NIC port (optional) N/A 12 NIC port (2) Enables you to remotely access iDRAC. For more information, see the iDRAC User's Guide at www.dell.com/ poweredgemanuals. Press the system ID button: • To locate a particular system within a rack. • To turn the system ID on or off. To reset iDRAC, press and hold the button for more than 16 seconds. NOTE: • To reset iDRAC using system ID, ensure that the system ID button is enabled in the iDRAC setup. • If the system stops responding during POST, press and hold the system ID button (for more than 5 seconds) to enter the BIOS progress mode. This port supports OCP 3.0. The NIC ports are integrated on the OCP card which is connected to the system board. The NIC ports are embedded on the LOM card that is connected to the system board. For more information about the ports, see the Technical Specifications section. System overview 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
Table 7. Rear view of the system
Item
Ports, panels, or slots
Icon
Description
1
Power supply unit (PSU 1)
For more information about the PSU configurations, see the
Technical Specifications
section.
2
PCIe expansion card riser
(slot 1)
N/A
The expansion card riser enables you to connect PCI Express
expansion cards. For more information about the expansion
cards that are supported on your system, see
Technical
Specifications
section.
3
PCIe expansion card riser
(slot 2)
N/A
The expansion card riser enables you to connect PCI Express
expansion cards. For more information about the expansion
cards that are supported on your system, see
Technical
Specifications
section.
4
USB 2.0 port (1)
This port is USB 2.0-compliant.
5
PCIe expansion card riser
(slot 3)
N/A
The expansion card riser enables you to connect PCI Express
expansion cards. For more information about the expansion
cards that are supported on your system, see
Technical
Specifications
section.
6
Power supply unit (PSU 2)
For more information about the PSU configurations, see the
Technical Specifications
section.
7
VGA port
Enables you to connect a display device to the system. For more
information, see the
Technical Specifications
section.
8
USB 3.0 port (1)
This port is USB 3.0-compliant.
9
iDRAC dedicated port
Enables you to remotely access iDRAC. For more information,
see the iDRAC User’s Guide at
www.dell.com/
poweredgemanuals
.
10
System identification button
Press the system ID button:
•
To locate a particular system within a rack.
•
To turn the system ID on or off.
To reset iDRAC, press and hold the button for more than 16
seconds.
NOTE:
•
To reset iDRAC using system ID, ensure that the
system ID button is enabled in the iDRAC setup.
•
If the system stops responding during POST, press
and hold the system ID button (for more than 5
seconds) to enter the BIOS progress mode.
11
OCP NIC port (optional)
N/A
This port supports OCP 3.0. The NIC ports are integrated on the
OCP card which is connected to the system board.
12
NIC port (2)
The NIC ports are embedded on the LOM card that is connected
to the system board.
For more information about the ports, see the
Technical Specifications
section.
System overview
11