Dell PowerEdge R6525 EMC Technical Specifications - Page 19

Ports and connectors specifications, USB ports specifications, IDSDM

Get Dell PowerEdge R6525 PDF manuals and user guides View all Dell PowerEdge R6525 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

NOTE: For more information about how to hot swap NVMe PCIe SSD U.2 device, see the Dell Express Flash NVMe PCIe SSD User's Guide at https://www.dell.com/support Browse all Products > Data Center Infrastructure > Storage Adapters & Controllers > Dell PowerEdge Express Flash NVMe PCIe SSD > Documentation > Manuals and Documents. Ports and connectors specifications USB ports specifications Table 18. PowerEdge R6525 system USB specifications Front Rear USB port type No. of ports USB port type No. of ports USB 2.0-compliant One port USB 3.0-compliant One ports Micro-USB 2.0 One compliant port USB 2.0-compliant One ports Internal USB port type No. of ports Internal USB 3.0- One compliant port NOTE: The micro USB 2.0 compliant port can only be used as an iDRAC Direct or a management port. NOTE: The USB 2.0 specifications provide a 5 V supply on a single wire to power connected USB devices. A unit load is defined as 100 mA in USB 2.0, and 150 mA in USB 3.0. A device may draw a maximum of 5 unit loads (500 mA) from a port in USB 2.0; 6 (900 mA) in USB 3.0. NOTE: The USB 2.0 interface can provide power to low-power peripherals but must adhere to USB specification. An external power source is required for higher-power peripherals to function, such as external CD/DVD Drives. NIC port specifications The PowerEdge R6525 system supports up to two 10/100/1000 Mbps Network Interface Controller (NIC) ports embedded on the LAN on Motherboard (LOM) and integrated on the optional OCP cards. Table 19. NIC port specification Feature LOM card OCP card (OCP 3.0) Specifications 1 GB x 2 1 GbE x 4, 10 GbE x 2, 25 GbE x 2, 25 GbE x 4, 50 GbE x 2, 100 GbE x 2 Serial connector specifications The PowerEdge R6525 system supports one optional card type serial connector, which is a 9-pin connector, Data Terminal Equipment (DTE), 16550-compliant. The optional serial connector card is installed similar to an expansion card filler bracket. VGA ports specifications The PowerEdge R6525 system supports one DB-15 VGA port that is located on the front and rear panel of the system. IDSDM The PowerEdge R6525 system supports optional Internal Dual SD module (IDSDM). The IDSDM supports two SD cards and is available in the following configurations: Technical specifications 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
NOTE:
For more information about how to hot swap NVMe PCIe SSD U.2 device, see the
Dell Express Flash NVMe PCIe
SSD User's Guide
at
Browse all Products > Data Center Infrastructure >
Storage
Adapters & Controllers > Dell PowerEdge Express Flash NVMe PCIe SSD > Documentation > Manuals and Documents.
Ports and connectors specifications
USB ports specifications
Table 18. PowerEdge R6525 system USB specifications
Front
Rear
Internal
USB port type
No. of ports
USB port type
No. of ports
USB port type
No. of ports
USB 2.0-compliant
port
One
USB 3.0-compliant
ports
One
Internal USB 3.0-
compliant port
One
Micro-USB 2.0
compliant port
One
USB 2.0-compliant
ports
One
NOTE:
The micro USB 2.0 compliant port can only be used as an iDRAC Direct or a management port.
NOTE:
The USB 2.0 specifications provide a 5 V supply on a single wire to power connected USB devices. A unit load is
defined as 100 mA in USB 2.0, and 150 mA in USB 3.0. A device may draw a maximum of 5 unit loads (500 mA) from a
port in USB 2.0; 6 (900 mA) in USB 3.0.
NOTE:
The USB 2.0 interface can provide power to low-power peripherals but must adhere to USB specification. An
external power source is required for higher-power peripherals to function, such as external CD/DVD Drives.
NIC port specifications
The PowerEdge R6525 system supports up to two 10/100/1000 Mbps Network Interface Controller (NIC) ports embedded on the LAN
on Motherboard (LOM) and integrated on the optional OCP cards.
Table 19. NIC port specification
Feature
Specifications
LOM card
1 GB x 2
OCP card (OCP 3.0)
1 GbE x 4, 10 GbE x 2, 25 GbE x 2, 25 GbE x 4, 50 GbE x 2, 100
GbE x 2
Serial connector specifications
The PowerEdge R6525 system supports one optional card type serial connector, which is a 9-pin connector, Data Terminal Equipment
(DTE), 16550-compliant.
The optional serial connector card is installed similar to an expansion card filler bracket.
VGA ports specifications
The PowerEdge R6525 system supports one DB-15 VGA port that is located on the front and rear panel of the system.
IDSDM
The PowerEdge R6525 system supports optional Internal Dual SD module (IDSDM).
The IDSDM supports two SD cards and is available in the following configurations:
Technical specifications
19