Dell PowerVault MD3000i Upgrading to SATA on MD3000i - Page 5

Updating Your MD3000i to Support, SATA II Disks - firmware upgrade

Get Dell PowerVault MD3000i PDF manuals and user guides View all Dell PowerVault MD3000i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

Updating Your MD3000i to Support SATA II Disks SATA Support Available in MD3000i Storage Arrays MD3000i storage arrays now support a total of 45 3.5" SAS and/or SATA II physical disks. The enclosure can contain a mixture of SAS and SATA physical disks; however, a disk group must consist of either SAS or SATA physical disks. If SAS disk groups and SATA II disk groups are configured in the same storage array, a hot spare must be available for each type and of equal or greater size than the disk group member drives. Both SAS and SATA physical disks are hot-pluggable, allowing you to remove and insert disks without shutting down your enclosure. NOTE: SATA I Physical disks are not supported in the MD3000i storage array enclosure. NOTE: Please follow the included guidelines to insert or remove physical disks from the enclosure. This document covers the steps you must perform to upgrade your MD3000i storage array to support SATA physical disks. Who Needs to Perform These Steps? You only need to perform these steps if your storage array controller firmware or Modular Disk Storage Manager versions are earlier than those shown in Table 1-1. You can check the MD Storage Manager version by going to the Support tab and clicking About Modular Disk Storage Manager. You can also determine the Controller Firmware Version by going to Support→Download Firmware→Download RAID Controller Module Firmware while connected to the MD3000i that is to be updated. The current firmware version will be displayed in the window. Updating to Support SATA II Disks 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
Updating to Support SATA II Disks
3
Updating Your MD3000i to Support
SATA II Disks
SATA Support Available in MD3000i Storage
Arrays
MD3000i storage arrays now support a total of 45 3.5” SAS and/or SATA II
physical disks. The enclosure can contain a mixture of SAS and SATA physical
disks; however, a disk group must consist of either SAS or SATA physical
disks. If SAS disk groups and SATA II disk groups are configured in the same
storage array, a hot spare must be available for each type and of equal or
greater size than the disk group member drives. Both SAS and SATA physical
disks are hot-pluggable, allowing you to remove and insert disks without
shutting down your enclosure.
NOTE:
SATA I Physical disks are not supported in the MD3000i storage array
enclosure.
NOTE:
Please follow the included guidelines to insert or remove physical disks
from the enclosure.
This document covers the steps you must perform to upgrade your MD3000i
storage array to support SATA physical disks.
Who Needs to Perform These Steps?
You only need to perform these steps if your storage array controller firmware
or Modular Disk Storage Manager versions are earlier than those shown in
Table 1-1. You can check the MD Storage Manager version by going to the
Support
tab and clicking
About Modular Disk Storage Manager
. You can also
determine the Controller Firmware Version by going to
Support
→
Download
Firmware
→
Download RAID Controller Module Firmware
while connected
to the MD3000i that is to be updated. The current firmware version will be
displayed in the window.