Dell XPS /Inspiron M170 Service Manual - Page 17

Removing the Display Bezel

Get Dell XPS /Inspiron M170 PDF manuals and user guides View all Dell XPS /Inspiron M170 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

1 M2.5 x 5-mm screws (4) 2 screw covers (2) 3 rubber display bumpers (6) 4 shoulder screws (2) Removing the Display Bezel CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. NOTICE: To avoid damaging the system board, you must remove the main battery before you begin working inside the computer. 1. Follow the instructions in "Before Working Inside Your Computer." 2. Remove the display assembly. 3. Remove the six screw-cover/rubber display bumpers. 4. Remove the two screw covers and the four shoulder screws. 5. Remove the four M2.5 x 5-mm screws at the corners of the display. NOTICE: Removal of the bezel from the top cover requires extreme care to avoid damage to the bezel. 6. Use your fingers to separate the bezel from the top cover by pulling the lower-right corner of the bezel down toward the bottom edge (A) of the display assembly to clear the tab on the bottom of the lower-right corner. Then pull the bezel toward the right side of the display assembly to clear the tab on the side (B) of the lower-right corner.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
Removing the Display Bezel
1.
Follow the instructions in "
Before Working Inside Your Computer
."
2.
Remove the
display assembly
.
3.
Remove the six screw-cover/rubber display bumpers.
4.
Remove the two screw covers and the four shoulder screws.
5.
Remove the four M2.5 x 5-mm screws at the corners of the display.
6.
Use your fingers to separate the bezel from the top cover by pulling the lower-right corner of the bezel down toward the bottom edge (A) of the display
assembly to clear the tab on the bottom of the lower-right corner. Then pull the bezel toward the right side of the display assembly to clear the tab on
the side (B) of the lower-right corner.
1
M2.5 x 5-mm screws (4)
2
screw covers (2)
3
rubber display bumpers (6)
4
shoulder screws (2)
CAUTION:
Before you begin the following procedure, see the safety instructions in the
Product Information Guide
.
NOTICE:
To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such
as the back panel) on the computer.
NOTICE:
To avoid damaging the system board, you must remove the main battery before you begin working inside the computer.
NOTICE:
Removal of the bezel from the top cover requires extreme care to avoid damage to the bezel.