Dell XPS 15 9510 Service Manual - Page 41

Installing the system board, Steps, Prerequisites

Get Dell XPS 15 9510 PDF manuals and user guides View all Dell XPS 15 9510 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Steps 1. Loosen the three captive screws that secure the display-assembly cable bracket to the system board. 2. Lift the display-assembly cable bracket off the system board. 3. Remove the two screws (M1.6x3) that secure the display-assembly cable holder to the palm-rest and keyboard assembly. 4. Disconnect the touch screen cable and camera cable. 5. Remove the screw (M1.6x3) that secures the wireless-card bracket to the system board. 6. Using a plastic scribe, disconnect the antenna cables from the wireless card. 7. Open the latch, and disconnect the fingerprint reader-board cable from the system board. 8. Remove the two screws (M2x4) that secure the USB Type-C bracket to the palm-rest and keyboard assembly. 9. Lift the USB Type-C bracket from the palm-rest and keyboard assembly. 10. Open the latch, and disconnect the keyboard-control board cable the system board. 11. Remove the two screws (M2x4) that secure the system board to the palm-rest and keyboard assembly. NOTE: The thermal plate is a part of the system board, DO NOT separate it from the system board. 12. Lift the system board off the palm-rest and keyboard assembly. Installing the system board Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. NOTE: The Service Tag of your computer is stored in the system board. Enter the Service Tag in the BIOS setup program after you replace the system board. NOTE: Replacing the system board removes any changes that you have made to the BIOS using the BIOS setup program. Make the appropriate changes again after you replace the system board. Removing and installing components 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
Steps
1.
Loosen the three captive screws that secure the display-assembly cable bracket to the system board.
2.
Lift the display-assembly cable bracket off the system board.
3.
Remove the two screws (M1.6x3) that secure the display-assembly cable holder to the palm-rest and keyboard assembly.
4.
Disconnect the touch screen cable and camera cable.
5.
Remove the screw (M1.6x3) that secures the wireless-card bracket to the system board.
6.
Using a plastic scribe, disconnect the antenna cables from the wireless card.
7.
Open the latch, and disconnect the fingerprint reader-board cable from the system board.
8.
Remove the two screws (M2x4) that secure the USB Type-C bracket to the palm-rest and keyboard assembly.
9.
Lift the USB Type-C bracket from the palm-rest and keyboard assembly.
10.
Open the latch, and disconnect the keyboard-control board cable the system board.
11.
Remove the two screws (M2x4) that secure the system board to the palm-rest and keyboard assembly.
NOTE:
The thermal plate is a part of the system board, DO NOT separate it from the system board.
12.
Lift the system board off the palm-rest and keyboard assembly.
Installing the system board
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
NOTE:
The Service Tag of your computer is stored in the system board. Enter the Service Tag in the BIOS setup program
after you replace the system board.
NOTE:
Replacing the system board removes any changes that you have made to the BIOS using the BIOS setup program.
Make the appropriate changes again after you replace the system board.
Removing and installing components
41