Denon DN-C635 Operating Instructions - Page 7

ENGLISH !6 Pitch Slider • Use this slider to adjust the play speed. Slide up to decrease the play speed, down to increase the play speed. @2 FOLDER button • When disc containing MP3 format files is loaded, in the stop mode press this button then the folder select mode is possible. !7 PROG. PLAY ON/OFF button • When this button is pressed while the PROG indicator is lit, the program play mode is set. • The button will not function during the A-B play mode. • The PROG. PLAY ON/OFF LED lights during the program play standby and play modes. • When the button is pressed during the program play standby or play mode, the program play mode is cleared. !8 PROGRAM IN button • Press this button to set the program input mode. • The button will not function during the play mode. • The PROG indicator flashes when in the program input mode. • The PROG indicator lights when a program is set. @3 A-B (A-B repeat) button • Use this to play a set section repeatedly. • When the button is pressed once during playback, that position is set as the A point and the "A-B" indicator flashes on the display. • When the button is pressed again, that position is set as the B point, the "A-B" indicator stops flashing (remaining lit), and the A-B section begins playing repeatedly. • When the button is pressed again, A-B repeat is canceled and the mode returns to the normal play mode. @4 Headphones jack • For private listening, you can connect your headphones to this jack. @5 PHONES LEVEL control • Use this adjust the output level of the headphones. !9 REPEAT button • Press this to perform repeat playback. @0 TIME button • The time display switches each time this button is pressed. ("REMAIN", "ELAPSED") @1 TITLE button • When the button is pressed, the text information (Disc title, track title, disc artist or track artits) is displayed. • When the button is pressed while in the stop mode with a disc containing an MP3 ID3-Tag loaded, the file name is displayed. When pressed during playback, the display switches as shown below. Elapsed time of currently playing track File name of currently playing track Title name Artist name Album name (2) Rear panel q BALANCED OUT connectors • These are active balanced outputs using XLR type connections. The CD's playback signals are output from these connectors. • Pin layout : 1. Common / 2. Hot / 3. Cold • Applicable connector : Cannon XLR-3-31 or equivalent. NOTE : • Do not short-circuit the hot or cold pin with the common pin. w LEVEL L/R controls • Use these controls to adjust the level of the audio signals from the BALANCED OUT connectors. e UNBALANCED OUT jacks • These are unbalanced outputs using RCA type jacks. r DIGITAL OUT jack • This is a coaxial output using an RCA type jack. • Signal format : SPDIF or IEC-958 Type II t Serial control port • This is serial remote connector. • Applicable connector : 9-pin D-sub (male) • Baud rate : 9600 bps • Pin layout RS-232C Pin No. Signal Name I / O 1 GND _ 6 NC _ 2 TxD O 7 NC _ 3 RxD I 8 NC _ 4 NC _ 9 NC _ 5 S. GROUND _ RS-422A Pin No. Signal Name I / O 1 GND _ 6 NC _ 2 TxD (RETURN) O 7 TxD O 3 RxD I 8 RxD (RETURN) I 4 NC _ 9 NC _ 5 S. GROUND _ y Parallel remote control port • This is a parallel remote connector. • Applicable connector : 25-pin D-sub (male) • Connecting signal layout Pin No. Signal Name I / O 1 FG _ 14 PLAY tally O TTL (Iol = 20mA) 2 PLAY command I HCMOS (Ii = 3mA) 15 PAUSE tally O TTL (Iol = 20mA) 3 PAUSE command I HCMOS (Ii = 3mA) 16 CUE tally O TTL (Iol = 20mA) 4 CUE command I HCMOS (Ii = 3mA) 17 INDEX 2/INDEX 3 tally O TTL (Iol = 20mA) 5 TRACK (+) command 18 Tally common I HCMOS (Ii = 3mA) _ 6 TRACK (-) command 19 Reserved I HCMOS (Ii = 3mA) _ 7 SEARCH (Fwd) command I HCMOS (Ii = 3mA) 20 Reserved _ 8 SEARCH (Rev) command I HCMOS (Ii = 3mA) 21 Reserved _ 9 FADER START command I HCMOS (Ii = 3mA) 22 Tally power supply _ +3.3V, 20mA 10 Command common _ (Ii = 10mA) 23 Command common _ 11 NC _ 24 EOM tally _ TTL (Iol = 20mA) 12 Reserved _ 25 Reserved _ 13 Reserved _ 7