Denon DVD-A1UDCI Owners Manual - English - Page 18

Getting Started Connections Setup Playback HDMI Control Function Information Troubleshooting Specifications ENGLISH Required Settings for HDMI Connection Setting HDMI video output n Make HDMI Output Signal and HDMI Control Function Settings "HDMI Setup" (vpage 25, 26) n Make the Video Output Signal Setting for the Connected Television "Video Setup" (vpage 26) n About HDMI Video Resolution Setting • Change the HDMI video resolution by pressing settings are underlined. Auto Source Direct (Auto) (Source direct) . Switch the output mode as follows. Default 480/576i (480/576 interlaced) 480/576P (480/576 progressive) 1080P24 (1080 progressive, 24-frame) 1080P (1080 progressive) 1080i (1080 interlaced) 720P (720 progressive) • If the HDMI resolution is not set to "Auto", set it to correspond with the resolution of your television. Images will not be projected normally if the television resolution and DVD-A1UDCI's output resolution do not match. • Audio and video will be temporarily interrupted if the power of the connected device currently playing back is turned off, or input is switched. • When you change the HDMI video resolution of the DVD-A1UDCI, it takes from a few seconds up to about 10 seconds for validation between the DVD-A1UDCI and the connected device. Audio/video is not output during this period. •When outputting deep colour or 1080p, etc., we recommend you use High Speed HDMI cable for enhanced high-quality playback. NOTE When the HDMI video resolution is set to "1080P24", HDMI video signals are output from the DVDA1UDCI with a resolution of 1080P and a frame rate of 24 frames per second, regardless of the video signals on the disc being played. Because of this, when playing discs containing video signals recorded with a frame rate of something other than 24 frames per second, the movement of the picture may be unnatural. If this happens, set the HDMI video resolution to something other than "1080P24". 1. Home Theater Playback - Playing Back Using Multi-channel System - Setting HDMI Audio Output • When you press and set "HDMI Setup" - "Audio Setup" to "Auto" (vpage 25) on the GUI menu, audio mode is set according to the connected device. • When you want to set the HDMI audio output separately, change according to the following table. • Refer to the owner's manual of the connected device regarding HDMI audio input specifications compatible with the connected device. Device to be connected Setting items About output signal and speaker settings Device with the following built-in decoder · Dolby TrueHD · Dolby Digital Plus · Dolby Digital · DTS-HD · DTS Auto DVD-A1UDCI outputs a bitstream signal that is decoded by the connected device. b In this case, you cannot make a speaker setting for HDMI audio with the DVD-A1UDCI. Make the setting with the connected device. b When outputting the Dolby TrueHD or DTS-HD audio, press and set "BD Audio Mode" to "HD Audio Output" (vpage 33). Device compatible with multi-channel HDMI audio input, but not capable of speaker setting for each channel Multi LPCM BM On Outputs multi-channel Linear PCM audio signals with speaker setting by the DVD-A1UDCI. b For speaker setting, on the GUI menu, "Audio Setup" - "7.1ch Audio Out"- "Multi Channel" - "Speaker Configuration" (vpage 27). b BM : Bass Management (means multi-channel speaker setting) Device compatible with multi-channel HDMI audio input, and capable of speaker setting for each channel Multi LPCM BM Off Output of multi-channel Linear PCM audio signals from the DVD-A1UDCI. Perform the speaker setting with the connected device. b BM : Bass Management (means multi-channel speaker setting) Device compatible with 2channel HDMI audio input 2ch Downmixed 2-channel Linear PCM audio signals are output from the DVD-A1UDCI. Perform the speaker setting with the connected device. Device not compatible with HDMI audio signal input Mute Audio signal are not output from the DVD-A1UDCI's HDMI terminal. Only video signals are output from the HDMI terminal. b Make the audio connection. 15