Denon DVD-A1UDCI Owners Manual - English - Page 31

Getting Started Connections Setup Playback HDMI Control Function Information Troubleshooting Specifications Setting items 7.1ch Audio Out Setting contents GCrossover Freq.H : Set the upper limit of the low frequency signals output from the subwoofer. • 40Hz/60Hz/80Hz/90Hz/100Hz/110Hz/120Hz/150Hz/200Hz/250Hz : Outputs at below set frequency, each speaker's bass signal output from the subwoofer. Set this according to the low frequency reproduction capabilities of the speakers you are using. • Advanced : Set the low frequency signals to be output from the signals of the respective speakers to the subwoofer. Front, Center, Surround, Surr. Back 40Hz/60Hz/80Hz/90Hz/100Hz/110Hz/120Hz/150Hz/200Hz/250Hz LFE / LFE+Main 80Hz/90Hz/100Hz/110Hz/120Hz/150Hz/200Hz/250Hz When, on the GUI menu, "Audio Setup" - "7.1ch Audio Out"- "Multi Channel" - "Speaker Configuration" - "Subwoofer" is set to "Yes" (vpage 27), you can select "LFE" or "LFE+Main". NOTE • Select "Large" or "Small" not according to the physical size of the speaker but according to the low frequency reproduction capabilities based on the frequency set at "Crossover Freq.". • On the GUI menu, if the "Audio Setup" - "7.1ch Audio Out"- "Multi Channel" - "Speaker Configuration" item setting is changed, other settings are automatically changed as well. GExampleH If you set "Front" to "Small", "Subwoofer" is set to "Yes" and "Large" cannot be selected for "Center", "Surround" and "Surr. Back". • Audio signal (sampling frequency, number of channels) from the HDMI output terminal may be restricted by the specification of the HDMI audio that can be input by the device at the other side. GExampleH If the HDMI audio specification of the device at the other side is the 5.1 channel, even when DVD-A1UDCI plays back by the 7.1 channel, the 5.1 channel audio is automatically output. In that case, the analog audio output becomes the 5.1 channel output as well. Setting items 7.1ch Audio Out ENGLISH Audio Setup Setting contents n Channel Level : Set the volume of the test tone to be the same when it is output from each speaker. GModeH : Select a test tone output method. • Auto : Automatically switch the test tone output speaker. • Manual : Manually switch the test tone output speaker. GStartH : Begin outputting the test tone. Front L / Center / Front R / Surround R / Surr. Back R / Surr. Back L / Surround L / Subwoofer b When the test tone output stops, press . GSW +10dBH : Increase the subwoofer output level by 10 dB. z • Off : Do not change the subwoofer output level. • On : Increase the subwoofer output level by +10 dB. GDefaultH : Reset all channel level settings to factory default. • No : Do not Reset. • Yes : Reset. n Distance : Set the distance between the listening position and each speaker. GFeetH or GMetersH : Set the unit of distance. GStepH : Set the minimum variable width of the distance. 1ft, 0.1ft, 0.1m, 0.01m GDefaultH : Reset all distance settings to factory default. Front L / Front R / Center / Subwoofer / Surround L / Surround R / Surr. Back L / Surr. Back R : Select the speaker you want to set, and set the distance. Set the value that is closest to the measured distance. 0 ~ 60ft or 0 ~ 18m • Default settings : Front/Center/Subwoofer : 12 feet (3.6 meters) Surround/Surr. Back : 10 feet (3.0 meters) • Set the difference in the distance betweem the speakers to less than 20 feet (6.0 meters). Subwoofer Mode LFE : Add the low frequency signal of the channel for which the speaker Set the type of low frequency size is set to "small" to the subwoofer signal and output it. signal to be output from the LFE+Main : Add the low frequency signal of all channels to the subwoofer subwoofer. signal and output it. z : "SW +10dB" cannot be set for "HDMI Setup" - "Audio Setup" - "Multi LPCM BM On" - "Channel Level" on the GUI menu. Remote control operation buttons :Displaying the menu Cancel the menu :Moves the cursor (Up/Down/Left/Right) :Decision the setting :Return to previous menu 28