Dewalt DCV5801H Instruction Manual - Page 9

Chargers, Charging Procedure Fig. 1, Indicator Light Operation, Charge Indicators

Get Dewalt DCV5801H PDF manuals and user guides View all Dewalt DCV5801H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

English • Do not place any object on top of the charger or place the charger on a soft surface that might block the ventilation slots and result in excessive internal heat. Place the charger in a position away from any heat source. The charger is ventilated through slots in the top and the bottom of the housing. • Do not operate the charger with a damaged cord or plug. • Do not operate the charger if it has received a sharp blow, been dropped or otherwise damaged in any way. Take it to an authorized service center. • Do not disassemble the charger; take it to an authorized service center when service or repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire. • Disconnect the charger from the outlet before attempting any cleaning. This will reduce the risk of electric shock. Removing the battery pack will not reduce this risk. • NEVER attempt to connect 2 chargers together. • The charger is designed to operate on standard 120 volt household electrical power. Do not attempt to use it on any other voltage. This does not apply to the vehicular charger. Chargers Be sure to read all safety instructions before using your charger. Consult the chart at the end of this manual for compatibility of chargers and battery packs. FIG. 1 Li-Ion Slide Battery NiCd/NiMH/Li-Ion Tower Battery Charging Procedure (Fig. 1) DANGER: Electrocution hazard. 120 volts are present at recessed terminals of the tower port. Do not probe with conductive objects. Electric shock or electrocution may result. 1. Plug the charger into an appropriate outlet before inserting the battery pack. 2. Insert the battery pack into the correct charger port, as shown in Figure 1, making sure the pack is fully seated in the charger. The red (charging) light will blink continuously indicating that the charging process has started. 3. The completion of charge will be indicated by the red light remaining ON continuously. The pack is fully charged and may be used at this time or left in the charger. Indicator Light Operation PACK CHARGING PACK CHARGED HOT/COLD DELAY PROBLEM PACK OR CHARGER PROBLEM POWERLINE Charge Indicators This charger is designed to detect certain problems that can arise. Problems are indicated by the red light flashing at a fast rate. If this occurs, re-insert the battery pack into the charger. If the problem persists, try a different battery pack to determine if the charger is working properly. If the new pack charges correctly, then the original pack is defective and should be returned to a service center or other 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
•
Do not place any object on top of the
charger or place the
charger on a soft surface that might block the ventilation
slots and result in excessive internal heat.
Place the charger
in a position away from any heat source. The charger is ventilated
through slots in the top and the bottom of the housing.
•
Do not operate the charger with a damaged cord or plug.
•
Do not operate the charger if it has received a sharp blow,
been dropped or otherwise damaged in any way.
Take it to
an authorized service center.
•
Do not disassemble the charger; take it to an authorized
service center when service or repair is required.
Incorrect
reassembly may result in a risk of electric shock, electrocution or fire.
•
Disconnect the charger from the outlet before attempting
any cleaning. This will reduce the risk of electric shock.
Removing the battery pack will not reduce this risk.
•
NEVER
attempt to connect 2 chargers together.
•
The charger is designed to operate on standard 120 volt
household electrical power. Do not attempt to use it on any
other voltage.
This does not apply to the vehicular charger.
Chargers
Be sure to read all safety instructions before using your charger.
Consult the chart at the end of this manual for compatibility of
chargers and battery packs.
FIG. 1
NiCd/NiMH/Li-Ion Tower Battery
Li-Ion Slide Battery
Charging Procedure (Fig. 1)
DANGER:
Electrocution hazard. 120 volts are present at recessed
terminals of the tower port. Do not probe with conductive objects.
Electric shock or electrocution may result.
1. Plug the charger into an appropriate outlet before inserting the
battery pack.
2. Insert the battery pack into the correct charger port, as shown
in Figure 1, making sure the pack is fully seated in the charger.
The red (charging) light will blink continuously indicating that the
charging process has started.
3. The completion of charge will be indicated by the red light
remaining ON continuously. The pack is fully charged and may
be used at this time or left in the charger.
Indicator Light Operation
PACK CHARGING
PACK CHARGED
HOT/COLD DELAY
PROBLEM PACK OR CHARGER
PROBLEM POWERLINE
Charge Indicators
This charger is designed to detect certain problems that can arise.
Problems are indicated by the red light flashing at a fast rate. If this
occurs, re-insert the battery pack into the charger. If the problem
persists, try a different battery pack to determine if the charger is
working properly. If the new pack charges correctly, then the original
pack is defective and should be returned to a service center or other
English
7