Dewalt DWV010 Instruction Manual - Page 10

Cleaning, Storage Fig. 1, Accessories - vacuum

Get Dewalt DWV010 PDF manuals and user guides View all Dewalt DWV010 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

English FIG. 9 T S 2. Line up filter threads (T) to vacuum head threads and using moderate force, turn filter clockwise until tight. NOTE: Use care to not damage filter material. 3. Place the vacuum head (C) onto the container and secure it by closing the canister latches (D). Cleaning WARNING: Blow dirt and dust out of all air vents with dry air at least once a week. Wear proper ANSI Z87.1 (CAN/CSA Z94.3) eye protection and proper NIOSH/OSHA/MSHA respiratory protection when performing this. WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth dampened only with water and mild soap. Never let any liquid get inside the motor. Storage (Fig. 1) 1. Empty the canister, refer to To Empty Canister under Operation. 2. Clean the vacuum inside and outside. 3. Clean or replace filters, refer to Filters. 4. Store the suction hose and the power cord as shown in the illustration. Secure hose with the hose strap (K) on the back of the vacuum. Place the unit in a dry room and secure it from unauthorized use. Accessories WARNING: Since accessories, other than those offered by DEWALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only DEWALT recommended accessories should be used with this product. Recommended accessories for use with your tool are available at extra cost from your local dealer or authorized service center. If you need assistance in locating any accessory, please contact DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-DEWALT (1-800-433-9258) or visit our website www.dewalt.com. OPTIONAL ACCESSORIES DWV9330 HEPA filter: Captures 99.97% of all particles greater than or equal to 0.3 microns. Required when picking up lead paint debris. DWE46100 5"-6" (127-152 mm) Cutting/tuckpointing shroud DWE46101 5"-6" (127-152 mm) Cutting/tuckpointing shroud kit DWE46150 5" (127 mm) Cutting/tuckpointing shroud 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
8
English
S
FIG. 9
T
2. Line up filter threads (T) to vacuum head threads and using
moderate force, turn filter clockwise until tight.
NOTE:
Use care to not damage filter material.
3. Place the vacuum head (C) onto the container and secure it by
closing the canister latches (D).
Cleaning
WARNING:
Blow dirt and dust out of all air vents with dry air at
least once a week. Wear proper ANSI Z87.1 (CAN/CSA Z94.3) eye
protection and proper NIOSH/OSHA/MSHA respiratory protection
when performing this.
WARNING:
Never use solvents or other harsh chemicals for
cleaning the non-metallic parts of the tool. These chemicals may
weaken the plastic materials used in these parts. Use a cloth
dampened only with water and mild soap. Never let any liquid get
inside the motor.
Storage (Fig. 1)
1. Empty the canister, refer to
To Empty Canister
under
Operation
.
2. Clean the vacuum inside and outside.
3. Clean or replace filters, refer to
Filters
.
4. Store the suction hose and the power cord as shown in the
illustration. Secure hose with the hose strap (K) on the back
of the vacuum. Place the unit in a dry room and secure it from
unauthorized use.
Accessories
WARNING:
Since accessories, other than those offered by
D
E
WALT, have not been tested with this product, use of such
accessories with this tool could be hazardous. To reduce the risk
of injury, only D
E
WALT recommended accessories should be used
with this product.
Recommended accessories for use with your tool are available
at extra cost from your local dealer or authorized service center.
If you need assistance in locating any accessory, please contact
D
E
WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD
21286, call 1-800-4-D
E
WALT (1-800-433-9258) or visit our website
www.dewalt.com.
OPTIONAL ACCESSORIES
DWV9330
HEPA filter: Captures 99.97% of all
particles greater than or equal to 0.3
microns. Required when picking up lead
paint debris.
DWE46100
5"–6" (127–152 mm)
Cutting/tuckpointing shroud
DWE46101
5"–6" (127–152 mm)
Cutting/tuckpointing shroud kit
DWE46150
5" (127 mm) Cutting/tuckpointing
shroud