Dewalt DXPW3425 Instruction Manual - Page 17

To Clean the Water Inlet Filter Fig. 10 - engine manual

Get Dewalt DXPW3425 PDF manuals and user guides View all Dewalt DXPW3425 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

English 5. Direct water supply into spray nozzle to back flush loosened particles for 30 seconds. 6. Reassemble the nozzle to the wand. 7. Reconnect spray wand to gun then turn on water supply. 8. Start pressure washer and place spray wand into high pressure setting to test. To Clean the Water Inlet Filter (Fig. 10) This filter screen (U) should be checked periodically and cleaned if necessary. 1. Remove the filter screen (U) by grasping the end and removing it from water inlet of pump. 2. Clean filter by flushing it with water on both sides. 3. Reinsert filter into water inlet of pump. Convex side faces out. NOTE: Do not operate pressure washer without filter properly installed. sTORAGE Engine Consult the engine instruction manual for the man­u­fac­tur­er's recommendations for storage. Pump The manufacturer recommends using SIMPSON® / POWERWASHER® Pump Guard or equivalent when storing the unit for more than 30 days and/or when freezing temperatures are expected. SIMPSON® / POWERWASHER® Pump Guard is environmentally friendly. NOTE: Using pump guard helps provide proper lubrication to the internal seals of the pump regardless of temperature or environment. NOTICE: Risk of property damage. Use only SIMPSON® / POWERWASHER® Pump Guard or equivalent. Other products could be corrosive and/or contain alcohol which may cause pump damage. 1. Turn off pressure washer and disconnect hoses from pump. 2. Unscrew bottle valve from Pump Guard bottle and remove seal. 3. Screw bottle valve back onto bottle. 4. Attach bottle to water inlet of pump. 5. Squeeze bottle to inject contents into pump. 6. With ignition switch off, simultaneously pull starter rope and squeeze bottle. Repeat until protector fluid exits pump outlet. NOTE: This step may require two people. Pressure Washer 1. Drain all water from high pressure hose, coil it and store it in cradle of the pressure washer handle. 2. With nozzle pointed down and the spray gun and wand in a vertical position, squeeze trigger to drain all water from spray gun and wand. Store in gun holder. 3. Store chemical hose so it is protected from dama­ ge. Caution: Risk of personal injury. Avoid placing hands between handle and frame when assembling to prevent pinching. NOTICE: Risk of property damage. Always store and transport unit in an upright position. Accessories Recommended accessories for use with your tool are available for purchase from your local dealer or authorized service center. If you need assistance in locating any accessory for your tool, please contact the FNA Group at www.dewaltpw.com, 1825 Greenleaf Avenue, Elk Grove Village, Il 60007, or call (877) FNA-GAS1. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
17
English
5. Direct water supply into spray nozzle to back flush loosened
particles for 30 seconds.
6. Reassemble the nozzle to the wand.
7. Reconnect spray wand to gun then turn on water supply.
8. Start pressure washer and place spray wand into high pressure
setting to test.
To Clean the Water Inlet Filter (Fig. 10)
This filter screen (U) should be checked periodically and cleaned if
necessary.
1. Remove the filter screen (U) by grasping the end and removing it
from water inlet of pump.
2. Clean filter by flushing it with water on both sides.
3. Reinsert filter into water inlet of pump. C
onvex
side faces out.
NOTE:
Do not operate pressure washer without filter properly
installed.
STORAGE
Engine
Consult the engine instruction manual for the manufacturer's
recommendations for storage.
Pump
The manufacturer recommends using SIMPSON
®
/ POWERWASHER
®
Pump Guard or equivalent when storing the unit for more than 30
days and/or when freezing temperatures are expected. SIMPSON
®
/
POWERWASHER
®
Pump Guard is environmentally friendly.
NOTE:
Using pump guard helps provide proper lubrication to the
internal seals of the pump regardless of temperature or environment.
NOTICE:
Risk of property damage. Use only SIMPSON
®
/
POWERWASHER
®
Pump Guard or equivalent. Other products could
be corrosive and/or contain alcohol which may cause pump damage.
1. Turn off pressure washer and disconnect hoses from pump.
2. Unscrew bottle valve from Pump Guard bottle and remove seal.
3. Screw bottle valve back onto bottle.
4. Attach bottle to water inlet of pump.
5. Squeeze bottle to inject contents into pump.
6. With ignition switch off, simultaneously pull starter rope and
squeeze bottle. Repeat until protector fluid exits pump outlet.
NOTE:
This step may require two people.
Pressure Washer
1. Drain all water from high pressure hose, coil it and store it in
cradle of the pressure washer handle.
2. With nozzle pointed down and the spray gun and wand in a
vertical position, squeeze trigger to drain all water from spray gun
and wand. Store in gun holder.
3. Store chemical hose so it is protected from damage.
CAUTION:
Risk of personal injury. Avoid placing hands between
handle and frame when assembling to prevent pinching.
NOTICE:
Risk of property damage. Always store and transport unit
in an upright position.
ACCESSORIES
Recommended accessories for use with your tool are available for
purchase from your local dealer or authorized service center. If you
need assistance in locating any accessory for your tool, please contact
the FNA Group at www.dewaltpw.com, 1825 Greenleaf Avenue, Elk
Grove Village, Il 60007, or call (877) FNA-GAS1.