Dymo Rhino 5200 Hard case Kit by DYMO User Guide - Page 8

Printing Fixed Length Labels, Printing Patch Panel Labels, Printing Module Marking Labels

Get Dymo Rhino 5200 Hard case Kit by DYMO PDF manuals and user guides View all Dymo Rhino 5200 Hard case Kit by DYMO manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Printing Fixed Length Labels Normally, the length of the label is determined by the length of the text entered. However, you may wish to make a label for a specific purpose that is a fixed length regardless of the length of the text. You can specify a fixed length for a label in 0.5 mm (0.2") increments between 10 mm (0.4") and 999.9 mm (40.0"). The preset fixed length is 40 mm (1.5"). Any change you make to the fixed length setting remains in effect until you change it. To set the label length 1. Press . 2. Use the arrow keys to increase or decrease the label length. 3. Press . If multiple copies of a fixed-length label are printed, cut marks are printed between each label. See Figure 9. Cut Marks Figure 9 Printing Patch Panel Labels Patch panel mode allows you to label a row of ports on a patch panel. You can select the distance between ports and serialize the label, or you can enter different label text for each port manually, and then print. The result is a long label with evenly spaced text for each port. 01 02 03 04 � To print a patch panel label using serialization 1. Press . 2. Enter the distance between each port and press . The default is 12 mm (0.5") and the value can be set in increments of 0.1 mm (0.005"). 3. Enter the text for the first position on the label. 4. Follow the directions in Serializing Your Labels on page 10 to serialize the text that will print on the label. To print a patch panel label manually 1. Press . 2. Enter the distance between each port and press . The default is 12 mm (0.5") and the value can be set in increments of 0.1 mm (0.005"). 3. Enter the text for the current position on the label and press G. 4. Repeat step 3 until all port labels are printed. 0 To clear the previous label text, press + . 5. Press + to feed the tape after the last port and then cut the label using the Cutter lever. Printing Module Marking Labels Module marking allows you to create a label for and electrical module rack that has a varying number of modules of different sizes placed on one DIN rail. X=1 ROOM1 HEATING ROOM1 LIGHT To print a module marking label 1. Press . 2. Enter the size of a single modular component and press . 88 Manual_RhinoPRO5000_WEU.indd 8 23-07-2004 10:51:34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
8
Printing Fixed Length Labels
Normally, the length of the label is determined by
the length of the text entered. However, you may
wish to make a label for a specific purpose that is a
fixed length regardless of the length of the text.
You can specify a fixed length for a label in 0.5 mm
(0.2”) increments between 10 mm (0.4”) and
999.9 mm (40.0”). The preset fixed length is 40 mm
(1.5”). Any change you make to the fixed length
setting remains in effect until you change it.
To set the label length
1. Press
.
2. Use the arrow keys to increase or decrease the
label length.
3. Press
If multiple copies of a fixed-length label are
printed, cut marks are printed between each label.
See Figure 9.
Figure 9
Printing Patch Panel Labels
Patch panel mode allows you to label a row of ports
on a patch panel. You can select the distance
between ports and serialize the label, or you can
enter different label text for each port manually, and
then print. The result is a long label with evenly
spaced text for each port.
To print a patch panel label using serialization
1. Press
.
2. Enter the distance between each port and
press
.
The default is 12 mm (0.5”) and the value can be
set in increments of 0.1 mm (0.005”).
3. Enter the text for the first position on the label.
4. Follow the directions in
Serializing Your Labels
on page 10 to serialize the text that will print on
the label.
To print a patch panel label manually
1. Press
.
2. Enter the distance between each port and
press
.
The default is 12 mm (0.5”) and the value can be
set in increments of 0.1 mm (0.005”).
3. Enter the text for the current position on the label
and press
G
.
4. Repeat step 3 until all port labels are printed.
To clear the previous label text, press
+
0
.
5. Press
+
to feed the tape after the last port
and then cut the label using the Cutter lever.
Printing Module Marking Labels
Module marking allows
you to create a label for
and electrical module
rack that has a varying
number of modules of
different sizes placed
on one DIN rail.
To print a module marking label
1. Press
.
2. Enter the size of a single modular component
and press
.
Cut Marks
01
02
03
04
�
HEATING
ROOM1
ROOM1
LIGHT
X=1
Manual_RhinoPRO5000_WEU.indd
8
23-07-2004
10:51:34