E-Z-GO 2Five Owner Manual - Page 68

Fig. 6, Initial Service Chart, BRAKE BURNISHING PROCEDURE

Get E-Z-GO 2Five PDF manuals and user guides View all E-Z-GO 2Five manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

OPERATING PROCEDURES Read all of this manual to become thoroughly familiar with this vehicle. Pay particular attention to all Notices, Cautions, Warnings, and Dangers. Remove the protective clear plastic from the seat bottom and back rest before placing the vehicle in service. ITEM Batteries Seats Brakes Tires SERVICE OPERATION Charge batteries Remove protective plastic covering Check master cylinder fluid level & brake operation Perform brake burnishing procedure Establish acceptable stopping distance Check air pressure (see SPECIFICATIONS) Fig. 6 Initial Service Chart BRAKE BURNISHING PROCEDURE: For new vehicles or after replacement of brake pads or rotors, it is recommended that approximately 20 stops with moderate braking from 20 mph to 5 mph should be made without coming to a complete stop. This procedure will assure that your new brakes will function to their full potential and maintain maximum wear resistance. Determine and record the braking distance required to stop the vehicle for future brake performance tests. 60 2Five Owner's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
OPERATING PROCEDURES
Read all of this manual to become thoroughly familiar with this vehicle. Pay particular attention to all Notices, Cautions, Warnings, and Dangers.
60
2Five Owner’s Guide
Remove the protective clear plastic from the seat bottom and back rest before placing the vehicle in ser-
vice.
Fig. 6
Initial Service Chart
BRAKE BURNISHING PROCEDURE:
For new vehicles or after replacement of brake pads or rotors, it is recommended that approximately 20
stops with moderate braking from 20 mph to 5 mph should be made without coming to a complete stop.
This procedure will assure that your new brakes will function to their full potential and maintain maximum
wear resistance.
Determine and record the braking distance required to stop the vehicle for future brake performance tests.
ITEM
SERVICE OPERATION
Batteries
Charge batteries
Seats
Remove protective plastic covering
Brakes
Check master cylinder fluid level & brake operation
Perform brake burnishing procedure
Establish acceptable stopping distance
Tires
Check air pressure (see SPECIFICATIONS)