Electrolux EI48HI55KS Complete Owner's Guide (Français) - Page 6

Location Requirements, Product dimensions

Get Electrolux EI48HI55KS PDF manuals and user guides View all Electrolux EI48HI55KS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

 Location requirements Location Requirements IMPORTANT: Observe all governing codes and ordinances. Have a qualified technician install the hood insert. It is the installer's responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located behind the left filter on the rear wall of the hood insert. The hood insert location should be away from strong draft areas, such as windows, doors and strong heating vents. Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance. The hood insert must be surrounded by a custom built enclosure with hood cabinet capable of supporting 75 lb (34 kg). Grounded electrical outlet is required. See "Electrical Requirements" section on page 5. All openings in ceiling and wall where canopy hood will be installed must be sealed. Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local codes. Cabinet Dimensions 30" (76.2 cm) for 30" models 36" (91.4 cm) for 36" models 48" (121.9 cm) for 48" models Hood insert cabinet must be capable of supporting 75 lb (34 kg) "X" bottom of canopy to cooking surface 22" (55.9 cm) Hood insert depth For Mobile Home Installations The installation of this hood insert must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280) or when such standard is not applicable, the standard for Manufactured Home IMPORTANT: Minimum distance "X": 24" (61 cm) from electric cooking surfaces. Minimum distance "X": 30" (76.2 cm) from gas cooking surfaces. Suggested maximum distance "X": 36" (91.4 cm). Product dimensions 36" & 48" models wiring knockout 8" (31.4 cm) 16" (12.2 cm) (29.2 cm) 16" (12.8 cm) 97/8" (25.11 cm) 30" model wiring knockout 15" (38 cm) for 30" models 18" (45.2 cm) for 36" models 24" (61 cm) for 48" models 11" (28 cm) 11" (28 cm) for 30" model 10 1/8" (25.7 cm) for 36 & 48" models 22" (55.9 cm) 22" (56 cm) for 30"models 271/2"(70 cm) for 36 & 48"models 245/16"(61.8 cm) for 30" models 30" (75.8 cm) for 36 & 48" models 30" (76.2 cm) for 30" models 36" (91.4 cm) for 36" models 48" (121.4 cm) for 48" models

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
6
Installation 1982 (Manufactured Home Sites, Commu-
nities and Setups) ANSI A225.1/NFPA 501A, or latest
edition, or with local codes.
Cabinet Dimensions
IMPORTANT:
Minimum distance “X”: 24” (61 cm) from electric cooking surfaces.
Minimum distance “X”: 30” (76.2 cm) from gas cooking surfaces.
Suggested maximum distance “X”: 36” (91.4 cm).
Location Requirements
IMPORTANT: Observe all governing codes and ordi-
nances. Have a qualified technician install the hood
insert. It is the installer’s responsibility to comply with
installation clearances specified on the model/serial
rating plate. The model/serial rating plate is located
behind the left filter on the rear wall of the hood
insert.
The hood insert location should be away from strong
draft areas, such as windows, doors and strong heat-
ing vents.
Cabinet opening dimensions that are shown must be
used. Given dimensions provide minimum clearance.
The hood insert must be surrounded by a custom built
enclosure with hood cabinet capable of supporting 75
lb (34 kg).
Grounded electrical outlet is required. See “Electrical
Requirements” section on page 5.
All openings in ceiling and wall where canopy hood
will be installed must be sealed.
For Mobile Home Installations
The installation of this hood insert must conform to the
Manufactured Home Construction Safety Standards,
Title 24 CFR, Part 328 (formerly the Federal Standard
for Mobile Home Construction and Safety, Title 24,
HUD, Part 280) or when such standard is not appli-
cable, the standard for Manufactured Home
“X” bottom of canopy to
cooking surface
Hood insert cabinet must be
capable of supporting
75 lb (34 kg)
22”
(55.9 cm)
Hood insert
depth
Location requirements
Product dimensions
30” (76.2 cm) for 30” models
36” (91.4 cm) for 36” models
48” (121.9 cm) for 48” models
9
7
/
8
” (25.11 cm)
22” (55.9 cm)
10 1/8” (25.7 cm) for 36 & 48” models
11” (28 cm)
15” (38 cm) for 30” models
18” (45.2 cm) for 36” models
24” (61 cm) for 48” models
8
”
(31.4 cm)
(29.2 cm)
16
” (12.2 cm)
16
”
(12.8 cm)
24
5
/
16
”(61.8 cm) for 30” models
30” (75.8 cm) for 36 & 48” models
30” (76.2 cm) for 30” models
36” (91.4 cm) for 36” models
48” (121.4 cm) for 48” models
22” (56 cm) for 30”models
27
1
/
2
”(70 cm) for 36 & 48”models
11” (28 cm) for 30” model
30” model
wiring knockout
36” & 48” models
wiring knockout