Electrolux EWFLW65H Installation Instructions - Page 4

Installation, Requirements - washers

Page 4 highlights

Installation Requirements E ectrica system requirements CIRCUIT - Individual, properly polarized and grounded 15 amp. branch circuit fused with 15 amp. time delay fuse or circuit breaker. POWER SUPPLY - 2 wire, with ground, 120 volt single phase, 60 Hz, Alternating Current. OUTLET RECEPTACLE - Properly grounded 3-prong receptacle to be located so the power supply cord is accessible when the washer is in an installed position. Groul wall Do not, under "_ any circumstances, | cut, remove, / or bypassthe | grounding prong, j) Powercord with supply cord having an equipment-grounding conductor and a grounding plug, the plug MUST be plugged into an appropriate, copper wired receptacle that is properly installed and grounded in accordance with all local codes and ordinances or in the absence of local codes, with the National Electrical Codes, ANSI/NFPA 70 (latest edition). If in doubt, call a licensed electrician. DO NOT cut off or alter the grounding prong on the power supply cord. In situations where a two-slot receptacle is present, it is the owner's responsibility to have a licensed electrician replace it with a properly grounded three prong grounding type receptacle. Water supply requirements Hot and cold water faucets MUST be installed within 42 inches (107 cm) of your washer's water inlet. The faucets MUST be 3/4 inch (1.9 cm) with threading for laundry hose connection. Water pressure MUST be between 30 and 120 psi. Pressure difference between hot and cold cannot be more than 10 psi. Your water department can advise you of your water pressure. Drain system requirements 1. Drain capable of eliminating 17 gals (64.3 L) per minute. 2. A standpipe diameter of 1-1/4 in. (3.18 cm) minimum. 3. The standpipe height above the floor should be: Minimum height: 24 in. (61 cm) Maximum height: 96 in. (244 cm) Grounding requirements 1. The washer MUST be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electrical shock by a path of least resistance for electrical current. 2. Since your washer is equipped with a power 96 _ (244cm) [lrlax. (61 C/r I) mln" m

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20

Installation
Requirements
E ectrica
system
requirements
CIRCUIT -
Individual,
properly polarized
and
grounded
15 amp. branch circuit
fused with 15
amp. time delay fuse or circuit
breaker.
POWER SUPPLY - 2 wire, with ground,
120 volt
single phase, 60 Hz, Alternating
Current.
OUTLET RECEPTACLE - Properly grounded
3-prong
receptacle to be located so the power
supply cord
is accessible
when the washer is in
an installed
position.
Groul
wall
Do not, under
"_
any circumstances, |
cut, remove,
/
or bypassthe
|
grounding prong,
j)
Power
cord
with
Grounding
requirements
supply cord having an equipment-grounding
conductor
and a grounding
plug, the plug
MUST be plugged into an appropriate,
copper
wired receptacle that is properly installed and
grounded
in accordance
with all local codes and
ordinances
or in the absence of local codes,
with the National Electrical Codes, ANSI/NFPA
70 (latest edition). If in doubt,
call a licensed
electrician.
DO NOT cut off or alter the grounding
prong on the power supply cord. In situations
where a two-slot
receptacle
is present, it is
the owner's responsibility
to have a licensed
electrician
replace it with a properly grounded
three prong grounding
type receptacle.
Water
supply
requirements
Hot and cold water faucets
MUST be installed
within 42 inches (107 cm) of your washer's
water
inlet. The faucets
MUST be 3/4 inch (1.9 cm) with
threading
for laundry hose connection.
Water pres-
sure MUST be between
30 and 120 psi. Pressure
difference
between
hot and cold cannot
be more
than 10 psi. Your water department
can advise you
of your water pressure.
Drain
system
requirements
1.
Drain capable of eliminating
17 gals (64.3 L) per
minute.
2. A standpipe
diameter
of 1-1/4 in. (3.18 cm)
minimum.
3. The standpipe
height above the floor should be:
Minimum
height:
24 in. (61 cm)
Maximum
height:
96 in. (244 cm)
96 _
(244cm)
[lrlax.
(61
C/r I)
mln"
m
1. The washer MUST be grounded.
In the event
of malfunction
or breakdown,
grounding
will
reduce the risk of electrical
shock by a path of
least resistance for electrical
current.
2. Since your washer is equipped
with a power