Epson EMP-7700 User Manual - Page 67

Maintaining and Transporting the Projector

Get Epson EMP-7700 - XGA LCD Projector PDF manuals and user guides
UPC - 010343832572
View all Epson EMP-7700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Follow these steps to replace the lamp: 1. Turn off the projector and unplug the power cord. 2. Allow the projector to cool down for at least an hour (if it has been on). 3. Use a screwdriver to loosen the retaining screw on the lamp cover. (You can't remove the screw from the cover.) When the screw is loose, slide off the lamp cover. ) warning Let the lamp cool before replacing it. If the lamp breaks, handle the shards carefully to avoid injury. 4. Use a screwdriver to loosen the two screws holding the lamp in place. (You can't remove these screws.) 5. Lift up the wire handle, as shown, and pull the lamp straight out. (The plastic flap above the lamp will flex out of the way as you remove the lamp.) handle Maintaining and Transporting the Projector 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
Maintaining and Transporting the Projector
61
Follow these steps to replace the lamp:
1.
Turn off the projector and unplug the power cord.
2.
Allow the projector to cool down for at least an hour (if it has
been on).
3.
Use a screwdriver to loosen the retaining screw on the lamp cover.
(You can’t remove the screw from the cover.)
When the screw is loose, slide off the lamp cover.
)
4.
Use a screwdriver to loosen the two screws holding the lamp in
place. (You can’t remove these screws.)
5.
Lift up the wire handle, as shown, and pull the lamp straight out.
(The plastic flap above the lamp will flex out of the way as you
remove the lamp.)
warning
Let the lamp cool before
replacing it. If the lamp
breaks, handle the shards
carefully to avoid injury.
handle