Epson Endeavor 486I User Manual - Page 121

Bracket in the Computer for instructions., Replace the drive mounting bracket. See Replacing

Get Epson Endeavor 486I PDF manuals and user guides View all Epson Endeavor 486I manuals
Add to My Manuals
Save this manual to your list of manuals

Page 121 highlights

3. Remove the screws securing the drive on both sides. 4. Reach behind the drive and gently push it out through the front of the bay; then pull it out of the slot. 5. Once you have removed the drive, replace the faceplate by inserting one side of the plate, then gently pressing on the other side until it snaps into place. 6. If you removed the only IDE device connected to the interface the device used, you may want to disconnect the device cable from the main system board and remove it from the computer. 7. Replace the drive mounting bracket. See "Replacing the Bracket in the Computer" for instructions. 8. If you have finished installing or removing drives, replace the computer's cover, as described under "Replacing the Cover" in Chapter 4. Then see "Using the Fixed Disk Setup 0ption"in Chapter 2 for instructions on defining your new drive configuration. Installing and Removing Slimline Drives 5-23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
3.
Remove the screws securing the drive on both sides.
4.
Reach behind the drive and gently push it out through the
front of the bay; then pull it out of the slot.
5.
Once you have removed the drive, replace the faceplate by
inserting one side of the plate, then gently pressing on the
other side until it snaps into place.
6.
If you removed the only IDE device connected to the
interface the device used, you may want to disconnect the
device cable from the main system board and remove it
from the computer.
7.
Replace the drive mounting bracket. See “Replacing the
Bracket in the Computer” for instructions.
8.
If you have finished installing or removing drives, replace
the computer’s cover, as described under “Replacing the
Cover” in Chapter 4. Then see “Using the Fixed Disk Setup
0ption”in Chapter 2 for instructions on defining your new
drive configuration.
Installing and Removing Slimline Drives
5-23