Epson Endeavor 486I User Manual - Page 131

the computer's cover, as described under Replacing

Get Epson Endeavor 486I PDF manuals and user guides View all Epson Endeavor 486I manuals
Add to My Manuals
Save this manual to your list of manuals

Page 131 highlights

2. Remove the four screws securing the drive to the drive bay. There are two screws on each side of the drive. 3. Slide the drive out the back of the bay. 4. If you removed the only IDE device connected to the interface the device used, you may want to disconnect the device cable from the interface on the main system board and remove it from the computer. 5. If you have finished installing or removing drives, replace the computer's cover, as described under "Replacing the Cover" in Chapter 4. Then see "Using the Fixed Disk Setup 0ption" in Chapter 2 for instructions on defining your new drive configuration. 6-10 Installing and Removing Tower Drives

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
2.
Remove the four screws securing the drive to the drive bay.
There are two screws on each side of the drive.
3.
Slide the drive out the back of the bay.
4.
If you removed the only IDE device connected to the interface
the device used, you may want to disconnect the device
cable from the interface on the main system board and
remove it from the computer.
5.
If you have finished installing or removing drives, replace
the computer’s cover, as described under “Replacing the
Cover” in Chapter 4. Then see “Using the Fixed Disk Setup
0ption” in Chapter 2 for instructions on defining your new
drive configuration.
6-10
Installing and Removing Tower Drives