Epson PowerLite 530 Projector for SMART Installation Guide - Short-Throw Wall - Page 26

Attach the attachment plate to the projector, 6. Attach the projector to the adjustment unit

Get Epson PowerLite 530 Projector for SMART PDF manuals and user guides View all Epson PowerLite 530 Projector for SMART manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

5. Attach the attachment plate to the projector 1. Place the projector upside down. 2. Attach the attachment plate to the projector using the hexagonal wrench (M4) and five M4 × 12 mm bolts with washers/spring washers. Attachment plate M4 × 12 mm hexagon socket head cap bolt with washer/spring washer (×5) Projector lens side Warning When installing or adjusting the wall mount, do not use adhesives to prevent the screws from loosening and do not use lubricants or oils on the projector slide plate. This may cause the case to crack and the projector to fall, resulting in personal injury or property damage. q Tighten the screws firmly. 6. Attach the projector to the adjustment unit 1. Slide the attachment plate onto the adjustment unit as shown below. 2. Partially tighten two M4 × 12 mm bolts at the points marked on the adjustment unit as shown below. M4 × 12 mm hexagon socket head cap bolt with washer M4 × 12 mm hexagon socket head cap bolt without washer Mark Attachment plate Adjustment unit 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
26
5.
Attach the attachment plate to the projector
1.
Place the projector upside down.
2.
Attach the attachment plate to the projector using the hexagonal wrench (M4) and five M4 × 12
mm bolts with washers/spring washers.
6.
Attach the projector to the adjustment unit
1.
Slide the attachment plate onto the adjustment unit as shown below.
2.
Partially tighten two M4 × 12 mm bolts at the points marked on the adjustment unit as shown
below.
q
Tighten the screws firmly.
M4 × 12 mm hexagon socket head cap
bolt with washer/spring washer (×5)
Projector lens side
Attachment plate
When installing or adjusting the wall mount, do not use adhesives to prevent the screws from
loosening and do not use lubricants or oils on the projector slide plate.
This may cause the
case to crack and the projector to fall, resulting in personal injury or property damage.
Warning
M4 × 12 mm hexagon socket head
cap bolt without washer
M4 × 12 mm hexagon socket
head cap bolt with washer
Mark
Attachment plate
Adjustment unit