Epson SureColor F7070 User Manual - Page 120

Problem Solver, When a Message is Displayed

Get Epson SureColor F7070 PDF manuals and user guides View all Epson SureColor F7070 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 120 highlights

Chapter 5 Problem Solver When a Message is Displayed If one of the following messages is displayed, read and follow the instructions below. Messages Prepare empty waste ink bottle. Chip Unit Error Chip unit not recognized. Reattach or replace. Chip Unit Error Chip unit cannot be recognized. Refill after matching ink pack with label? Chip unit expended.. Command Error Check print settings on RIP. Unit Matching Error Check combination of Media Feeding Unit and Auto Take-up Reel Unit. Then restart printer. F/W Install Error Firmware update failed. Restart the printer. Auto Take-up Reel Unit stopped. What to do The waste ink bottle is getting full. Ready a new waste ink bottle. See "Options and Consumable Products" on page 129. Remove and reinsert the chip unit. If the same error still occurs, replace with a new chip unit. See "Chip Unit Replacement and Ink Refills" on page 98. Condensation may have formed inside the tank. Keep at room temperature for at least four hours. See "Notes on Handling Ink Packs and Ink Tanks" on page 24. Use only the chip units from specified Epson ink packs. You cannot use unspecified Epson ink packs. See "Options and Consumable Products" on page 129. The chip unit is nearing the end of its service life. Obtain an ink pack of the appropriate color as soon as possible. See "Options and Consumable Products" on page 129 and "Notes on Handling Ink Packs and Ink Tanks" on page 24. Press W and select Job Cancel. Check that the installed software RIP is compatible with the printer. The standard media feeding unit is used only with the standard auto take-up reel unit, the heavy roll media feeding unit only with the heavy roll auto take-up reel unit. If you have mismatched the feeding and take-up reel units, turn the printer off and install the correct equipment. See the Setup Guide and the Heavy Media Roll System Setup Guide. Turn the printer off, wait for a few minutes, and then turn on the printer again. Use EPSON LFP Remote Panel 2 to update the firmware again. If this message appears on the LCD panel again, contact your dealer or Epson Support. Media is not correctly attached to the auto take-up reel unit. Press the W button and select Job Cancel to cancel printing. Flip the Auto switch on the auto take-up reel unit to Off, then flip it back and reattach the media to the auto take-up reel unit. See "Media Loading and Take-Up" on page 52. Problem Solver 120

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
Problem Solver
120
Chapter 5
Problem Solver
When a Message is Displayed
If one of the following messages is displayed, read and follow the instructions below.
Messages
What to do
Prepare empty waste ink bottle.
The waste ink bottle is getting full. Ready a new waste ink bottle. See
“Options and
Consumable Products” on page 129.
Chip Unit Error
Chip unit not recognized.
Reattach or replace.
Remove and reinsert the chip unit. If the same error still occurs, replace with a new chip
unit. See
“Chip Unit Replacement and Ink Refills” on page 98.
Condensation may have formed inside the tank. Keep at room temperature for at least
four hours. See
“Notes on Handling Ink Packs and Ink Tanks” on page 24.
Chip Unit Error
Chip unit cannot be recognized.
Refill after matching ink pack with
label?
Use only the chip units from specified Epson ink packs.
You cannot use unspecified Epson ink packs.
See “Options and Consumable Products” on page 129.
Chip unit expended..
The chip unit is nearing the end of its service life. Obtain an ink pack of the appropriate
color as soon as possible.
See
“Options and Consumable Products” on page 129 and “Notes on Handling Ink Packs
and Ink Tanks” on page 24.
Command Error
Check print settings on RIP.
Press
W
and select
Job Cancel
. Check that the installed software RIP is compatible with
the printer.
Unit Matching Error
Check combination of Media
Feeding Unit and Auto Take-up
Reel Unit.
Then restart printer.
The standard media feeding unit is used only with the standard auto take-up reel unit,
the heavy roll media feeding unit only with the heavy roll auto take-up reel unit. If you
have mismatched the feeding and take-up reel units, turn the printer off and install the
correct equipment.
See the S
etup Guide
and the
Heavy Media Roll System Setup Guide
.
F/W Install Error
Firmware update failed.
Restart the printer.
Turn the printer off, wait for a few minutes, and then turn on the printer again.
Use EPSON LFP Remote Panel 2 to update the firmware again.
If this message appears on the LCD panel again, contact your dealer or Epson Support.
Auto Take-up Reel Unit stopped.
Media is not correctly attached to the auto take-up reel unit.
Press the
W
button and select
Job Cancel
to cancel printing.
Flip the Auto switch on the auto take-up reel unit to Off, then flip it back and reattach the
media to the auto take-up reel unit.
See
“Media Loading and Take-Up” on page 52.