Epson TM-P60 User Guide - Page 12

Battery Recharging, Installing or Replacing Roll Paper - time out

Get Epson TM-P60 - Mobilink B/W Thermal Line Printer PDF manuals and user guides View all Epson TM-P60 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

English CAUTION: There is risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. 1. Slide the battery cover to open it. 2. Install or remove the battery and close the cover. 3. If you use the AC adapter, plug in the connector as shown in illustration A. Battery Recharging WARNING: Be sure to charge the battery that came with the printer. Using a battery other than the one specified may cause fire, explosion, leakage, overheating or other damage. Note: The battery can be charged only when the temperature is 0 ~ 40°C (32 ~ 104°F). 1. Be sure that the printer is turned off and the battery to be charged is installed. 2. Connect the AC adapter to the printer (see illustration A). 3. Recharging will now be started. Recharging will take approximately 5 hours with the AC adapter, or if you use the fast recharger (option), recharging will take approximately 2.5 hours. For detailed information for the fast recharger (option), see its instructions. The times described above are the times taken to charge a battery pack that is fully discharged. Installing or Replacing Roll Paper See illustration D. CAUTION: Be sure to use roll paper that meets the specifications. Note: Do not use paper rolls that have the paper glued to the core. 1. Press the open button to open the roll paper cover. 2. Remove the used roll paper core if there is one, and insert the new roll paper. Note: Note the direction the paper comes off the roll. 3. Pull out some paper, close the cover, and tear off the paper with the manual cutter. Installing or Replacing Roll Paper Vertically You can hang the printer vertically on a belt using a clip on the back of the printer or a neck strap provided as an option. When you use the printer vertically, follow the steps below to install roll paper. 1. Press the open button to open the roll paper cover. 2. Remove the used roll paper core if there is one. 3. Set the new roll paper on the inside of the roll paper cover. See ➀ in illustration D. Note: Note the direction the paper comes off the roll. 4. Pull the leading edge of the roll paper. See ➁ in illustration D. 8 TM-P60 User's Manual (IEEE802.11b)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
8
TM-P60 User’s Manual (IEEE802.11b)
English
CAUTION:
There is risk of explosion if the battery is replaced by an incorrect type. Dispose
of used batteries according to the instructions.
1.
Slide the battery cover to open it.
2.
Install or remove the battery and close the cover.
3.
If you use the AC adapter, plug in the connector as shown in illustration
A
.
Battery Recharging
WARNING:
Be sure to charge the battery that came with the printer. Using a battery other
than the one specified may cause fire, explosion, leakage, overheating or
other damage.
Note:
The battery can be charged only when the temperature is 0 ~ 40°C (32 ~ 104°F).
1.
Be sure that the printer is turned off and the battery to be charged is installed.
2.
Connect the AC adapter to the printer (see illustration
A
).
3.
Recharging will now be started.
Recharging will take approximately 5 hours with the AC adapter, or if you use the
fast recharger (option), recharging will take approximately 2.5 hours. For detailed
information for the fast recharger (option), see its instructions. The times described
above are the times taken to charge a battery pack that is fully discharged.
Installing or Replacing Roll Paper
See illustration
D
.
CAUTION:
Be sure to use roll paper that meets the specifications.
Note:
Do not use paper rolls that have the paper glued to the core.
1.
Press the open button to open the roll paper cover.
2.
Remove the used roll paper core if there is one, and insert the new roll paper.
Note:
Note the direction the paper comes off the roll.
3.
Pull out some paper, close the cover, and tear off the paper with the manual
cutter.
Installing or Replacing Roll Paper Vertically
You can hang the printer vertically on a belt using a clip on the back of the printer
or a neck strap provided as an option. When you use the printer vertically, follow
the steps below to install roll paper.
1.
Press the open button to open the roll paper cover.
2.
Remove the used roll paper core if there is one.
3.
Set the new roll paper on the inside of the roll paper cover. See
➀
in
illustration
D
.
Note:
Note the direction the paper comes off the roll.
4.
Pull the leading edge of the roll paper. See
➁
in illustration
D
.