Epson TM-P60 User Guide - Page 14

How to Set Up the Network, Preparation - technical reference guide

Get Epson TM-P60 - Mobilink B/W Thermal Line Printer PDF manuals and user guides View all Epson TM-P60 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

English How to Set Up the Network Preparation Printing a Status Sheet Make sure the printer is turned off and the roll paper cover is closed properly. Power on the printer and then open the roll paper cover. Hold down the FEED button until the printer beeps (about 2 seconds). Close the roll paper cover. The printer prints the parameters for the printer. You can check all setting values necessary (SSID, Network mode, IP address, Subnet mask, Gateway address) for the network connection. Connection Set the setting of the host PC and AP to match the network setting that you have confirmed with the status sheet. Note: The AP mentioned above applies only to the printer if it is in the InfraStructure mode (you can check it with the status sheet). You can check whether the connection to the printer has been correctly done by inputting the ping command through the command prompt. Example: Ping 192.168.192.168 Note: Although the example shows the address 192.168.192.168, use whatever IP address is reported on the status sheet. Because the default IP addresses for all the wireless printers are the same, you should power on and configure only one printer at a time. Resetting the Printer to Factory Defaults Open the roll paper cover. Turn on the printer's power while pressing down the FEED button. Press the FEED button 6 times. Close the roll paper cover. The printer prints the procedure for resetting. Follow the procedure. Host Operating System Windows® XP and 2000 are the recommended host PC operating systems because they have built-in TCP/IP support. Setup There are two methods for the setup. For details, see the TM-P60 Technical Reference Guide. ❏ Using a Web browser 1. Start Windows Internet Explorer (or your Web browser). 2. Input the IP address of the TM-P60 in the browser address bar and press Enter (Example: http://192.168.192.168 [default]). 3. The browser displays a dialog box requesting a user name and password. Click OK without entering any user name or password. (If you have changed the user name and password, you need to input them.) 4. You can modify the parameters by following the menus. You must click Submit to send the change to the printer and then click Reset to make the submission effective on each Web page. If you change the IP address, SSID, etc., you have to change the setting of the host PC and AP to match the printer's setting. 10 TM-P60 User's Manual (IEEE802.11b)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
10
TM-P60 User’s Manual (IEEE802.11b)
English
How to Set Up the Network
Preparation
Printing a Status Sheet
Make sure the printer is turned off and the roll paper cover is closed properly.
Power on the printer and then open the roll paper cover. Hold down the
FEED
button until the printer beeps (about 2 seconds). Close the roll paper cover. The
printer prints the parameters for the printer. You can check all setting values
necessary (SSID, Network mode, IP address, Subnet mask, Gateway address) for
the network connection.
Connection
Set the setting of the host PC and AP to match the network setting that you have
confirmed with the status sheet.
Note:
The AP mentioned above applies only to the printer if it is in the InfraStructure mode (you
can check it with the status sheet).
You can check whether the connection to the printer has been correctly done by
inputting the ping command through the command prompt.
Example: Ping 192.168.192.168
Note:
Although the example shows the address 192.168.192.168, use whatever IP address is
reported on the status sheet.
Because the default IP addresses for all the wireless printers are the same, you
should power on and configure only one printer at a time.
Resetting the Printer to Factory Defaults
Open the roll paper cover. Turn on the printer’s power while pressing down the
FEED
button. Press the
FEED
button 6 times. Close the roll paper cover. The printer
prints the procedure for resetting. Follow the procedure.
Host Operating System
Windows
®
XP and 2000 are the recommended host PC operating systems because
they have built-in TCP/IP support.
Setup
There are two methods for the setup. For details, see the T
M-P60 Technical
Reference Guide
.
❏
Using a Web browser
1.
Start Windows Internet Explorer (or your Web browser).
2.
Input the IP address of the TM-P60 in the browser address bar and press
Enter
(Example: http://192.168.192.168 [default]).
3.
The browser displays a dialog box requesting a user name and password.
Click
OK
without entering any user name or password. (If you have changed
the user name and password, you need to input them.)
4.
You can modify the parameters by following the menus. You must click
Submit
to send the change to the printer and then click
Reset
to make the
submission effective on each Web page. If you change the IP address, SSID,
etc., you have to change the setting of the host PC and AP to match the
printer’s setting.