Epson WorkForce 600 Quick Guide - Page 37

Cleaning the Print Head

Get Epson WorkForce 600 - All-in-One Printer PDF manuals and user guides View all Epson WorkForce 600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Cleaning the Print Head If print quality has declined and the nozzle check indicates clogged nozzles, you can clean the print head. Print head cleaning uses ink, so clean it only if necessary. Note: You cannot clean the print head if an ink cartridge is expended, and may not be able to clean it when a cartridge is low. You must replace the cartridge first (see page 40). 1. Load letter-size plain paper in the sheet feeder. 2. Press the Home button. 3. Press l or r to select Setup and press OK. 4. Press l or r to select Maintenance and press OK. You see this screen: 5. Select Head Cleaning and press OK. 6. Press x Start. Cleaning takes about 2 minutes. When it's finished, you see a message on the display screen. Caution: Never turn off the printer during a cleaning cycle or you may damage it. 7. Select Nozzle Check and press OK. Then press x Start to run a nozzle check and confirm that the print head is clean. 8. Select Finish Nozzle Check and press OK when you're done. Note: If you don't see any improvement after cleaning the print head four times, turn off your WorkForce 600 Series and wait at least six hours to let any dried ink soften. Then try printing again. If you do not use your WorkForce 600 Series often, it is a good idea to print a few pages at least once a month to maintain good print quality. Cleaning the Print Head 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Cleaning the Print Head
37
Cleaning the Print Head
If print quality has declined and the nozzle check indicates clogged nozzles, you
can clean the print head. Print head cleaning uses ink, so clean it only if necessary.
Note:
You cannot clean the print head if an ink cartridge is expended, and may not be able to
clean it when a cartridge is low. You must replace the cartridge first (see page 40).
1.
Load letter-size plain paper in the sheet feeder.
2.
Press the
Home
button.
3.
Press
l
or
r
to select
Setup
and press
OK
.
4.
Press
l
or
r
to select
Maintenance
and press
OK
.
You see this screen:
5.
Select
Head Cleaning
and press
OK
.
6.
Press
x
Start
.
Cleaning takes about 2 minutes. When it’s finished,
you see a message on the display screen.
Caution:
Never turn off the printer during a cleaning cycle or you may damage it.
7.
Select
Nozzle Check
and press
OK
. Then press
x
Start
to run a nozzle check
and confirm that the print head is clean.
8.
Select
Finish Nozzle Check
and press
OK
when you’re done.
Note:
If you don’t see any improvement after cleaning the print head four times, turn off your
WorkForce 600 Series and wait at least six hours to let any dried ink soften. Then try
printing again.
If you do not use your WorkForce 600 Series often, it is a good idea to print a few pages
at least once a month to maintain good print quality.