Eureka LightSpeed 4700D Owners Manual - Page 20

How To Maintain - belt

Get Eureka LightSpeed 4700D PDF manuals and user guides View all Eureka LightSpeed 4700D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

FIG. 19a ENGLISH HOW TO MAINTAIN The instructions in this booklet serve as a guide to routine maintenance. To avoid unnecessary service calls, check the dust cup, belt, and brushroll often. Brushroll The brushroll turns as it sweeps and combs the carpet nap. Remove hair and threads from the brushroll so it continues brushing the carpet. To maintain the most efficient cleaning, the bristles must touch the carpet. To test the bristle length, hold a ruler against the underneath side of the cleaner. If the bristles no longer touch the ruler, replace the brushroll. Brushroll Belt Brushroll Performance Window (FIG. 19). To check condition of belt watch to see if white dots on belt are moving through the performance window (FIG. 19a). This indicates the brushroll is turning. The brushroll belt turns the brushroll to agitate, sweep, and comb the carpet nap. Check the belt regularly to be sure it is in good condition. Replace the belt if it stretches, cracks or loses tension. Cut away any hair or threads wound around the brushroll or the belt pulley because the buildup could cause the belt to rotate unevenly. FIG. 19 To Change Belt CAUTION: Turn off the switch and unplug the electrical cord before replacing belt. Motor shaft can become hot during normal use. To prevent injury, avoid touching the motor shaft when checking the belt (FIG. 20). Step 1: Lower handle to floor to change belt. Step 2: Remove two screws to release hood. Lift hood to expose belt and brushroll (FIG. 19). Step 3: Lift left end of brushroll and pull out of base. Step 4: Remove and discard belt. Step 5: Clean debris from brushroll area. Step 6: Place new belt around motor shaft. Step 7: Place belt around right side of brushroll. Step 8: Pull right side of brushroll to stretch belt. Secure right end cap into base. Step 9: Align left end cap with square in base. Push end cap into place. Step 10: Rotate brushroll to position belt on brushroll pulley. Step 11: Replace the hood. Step 12: Tighten screws. Use replacement belt, Style U 54312 or Style EXT-U 61120. 20 FIG. 20 (CONTINUED)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
20
FIG. 19
FIG. 20
ENGLISH
HOW TO MAINTAIN
The instructions in this booklet serve as a guide to routine maintenance. To
avoid unnecessary service calls, check the dust cup, belt, and brushroll often.
Brushroll
The brushroll turns as it sweeps and combs the carpet nap. Remove hair
and threads from the brushroll so it continues brushing the carpet. To
maintain the most efficient cleaning, the bristles must touch the carpet.
To test the bristle length, hold a ruler against the underneath side of the
cleaner. If the bristles no longer touch the ruler, replace the brushroll.
Brushroll Belt
Brushroll Performance Window
(FIG. 19). To check condition of belt
watch to see if white dots on belt are moving through the performance
window (FIG. 19a). This indicates the brushroll is turning.
The brushroll belt turns the brushroll to agitate, sweep, and comb the carpet
nap. Check the belt regularly to be sure it is in good condition. Replace the
belt if it stretches, cracks or loses tension. Cut away any hair or threads
wound around the brushroll or the belt pulley because the buildup could
cause the belt to rotate unevenly.
To Change Belt
CAUTION: Turn off the switch and unplug the electrical cord before
replacing belt. Motor shaft can become hot during normal
use. To prevent injury, avoid touching the motor shaft
when checking the belt (FIG. 20).
Step 1:
Lower handle to floor to change belt.
Step 2:
Remove two screws to release hood. Lift hood to expose belt and
brushroll (FIG. 19).
Step 3:
Lift left end of brushroll and pull out of base.
Step 4:
Remove and discard belt.
Step 5:
Clean debris from brushroll area.
Step 6:
Place new belt around motor shaft.
Step 7:
Place belt around right side of brushroll.
Step 8:
Pull right side of brushroll to stretch belt. Secure right end cap
into base.
Step 9:
Align left end cap with square in base. Push end cap into place.
Step 10:
Rotate brushroll to position belt on brushroll pulley.
Step 11:
Replace the hood.
Step 12:
Tighten screws.
Use replacement belt, Style U 54312 or Style EXT-U 61120.
(CONTINUED)
FIG. 19a