Fisher and Paykel OR36SDBMX1 User Guide - Page 13

Caution, Lighting Gas Burners Fitted With Flame Failure, Safety Device Dual Burner

Get Fisher and Paykel OR36SDBMX1 PDF manuals and user guides View all Fisher and Paykel OR36SDBMX1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

LIGHTING GAS BURNERS FITTED WITH FLAME FAILURE SAFETY DEVICE (Dual burner) In order to light the burner, you must: 1. Push and turn the dial in an counter-clockwise direction to the position (ma- ximum rate of inner + outer crown); push in and hold the dial until the flame has been lit (fig. 2.4). The sparks produced by the electrode situated inside the relative burner will light the flame. In the event that the local gas supply conditions makes it difficult to light the burner in position , try again with the dial in position . 2. Wait for about ten seconds after the gas burner has been lit before letting go the dial (safety device activation delay). 3. Adjust the gas valve to the desired position. If there is no mains electrical supply, the burners can be used with no restriction. In that case, in order to light the burner, you must: 1. Bring a lighted match close to the burner (as per side figure) and keep it in place until the burner has been ignited. 2. Push and turn the dial in an counter-clockwise direction up to the position (maximum rate of inner + outer crown); push in and hold the dial until the flame has been lit (fig. 2.4). In the event that the local gas supply conditions makes it difficult to light the burner in position , try again with the dial in position . 3. Wait for about ten seconds after the gas burner has been lit before letting go the dial (safety device activation delay). 4. Adjust the gas valve to the desired position. If the burner flame should go out for some reason, the safety valve will automatically stop the gas flow. To re-light the burner, return the dial to the closed OFF position, wait for at least 1 minute and then repeat the lighting procedure. If your local gas supply makes it difficult to light the burner with the dial set to maximum, set the dial to minimum and repeat the operation. N.B. When the range is not being used, set the gas dials to their OFF positions. If the range will not be used for an extended period of time, it is recommended that the gas shut off valve in the main supply line be closed. Caution! The range becomes very hot during operation. Keep children well out of reach. 2 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
13
13
2
Caution!
The range becomes very hot during operation.
Keep children well out of reach.
LIGHTING GAS BURNERS FITTED WITH FLAME FAILURE
SAFETY DEVICE (Dual burner)
In order to light the burner, you must:
1.
Push and turn the dial in an counter-clockwise direction to the position
(ma-
ximum rate of inner + outer crown); push in and hold the dial until the
fl
ame has been
lit (
fi
g. 2.4).
The sparks produced by the electrode situated inside the relative burner will light
the
fl
ame.
In the event that the local gas supply conditions makes it dif
fi
cult to light the burner
in position
, try again with the dial in position
.
2.
Wait for about ten seconds after the gas burner has been lit before letting go the dial
(safety device activation delay).
3.
Adjust the gas valve to the desired position.
If there is no mains electrical supply, the burners can be used with no restriction.
In that case, in order to light the burner, you must:
1.
Bring a lighted match close to the burner (as per side
fi
gure) and keep it in place until
the burner has been ignited.
2.
Push and turn the dial in an counter-clockwise direction up to the position
(maximum rate of inner + outer crown); push in and hold the dial until the
fl
ame has
been lit (
fi
g. 2.4).
In the event that the local gas supply conditions makes it dif
fi
cult to light the burner
in position
, try again with the dial in position
.
3.
Wait for about ten seconds after the gas burner has been lit before letting go the dial
(safety device activation delay).
4.
Adjust the gas valve to the desired position.
If the burner
fl
ame should go out for some reason, the safety valve will automatically stop
the gas
fl
ow.
To re-light the burner, return the dial to the closed
OFF
position, wait for at least 1 minute
and then repeat the lighting procedure.
If your local gas supply makes it dif
fi
cult to light the burner with the dial set to maximum,
set the dial to minimum and repeat the operation.
N.B. When the range is not being used, set the gas dials to their
OFF
positions. If the range will not be used for an extended period of time, it
is recommended that the gas shut off valve in the main supply line be
closed.