Fluke 414D Fluke 414D, 419D, 424D Laser Distance - Manual - Page 35

Memory (419D/424D), Maintenance, Disable the Meter

Get Fluke 414D PDF manuals and user guides View all Fluke 414D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

6. Make sure that the Meter is perpendicular to the wall. 7. Push  to trigger the bottom target (3) measurement. The result is the partial vertical distance between target 1 and target 2. The third measurement shows in the secondary line. As an option, use the tracking mode on one or more targets. To use tracking mode: 1. Push and hold  for 2 seconds to start tracking mode. 2. Move the laser side to side and up and down on the ideal horizontal target point. 3. Push  to stop the tracking mode. Memory (419D/424D) You can recall a previous measurement from memory, for example, the height of a room. The Meter stores a maximum of 20 displays. To recall: 1. Push  1x. 2. Push  and  to move through the stored displays. Laser Distance Meter Memory (419D/424D)  and the memory ID show on the display. 3. Push  for 2 seconds to use the value shown in the Summary line for further calculations. To delete: 1. Push  and  at the same time. The Meter deletes all the stored values in memory. Maintenance Maintenance and calibration is not necessary for the Meter. To keep the Meter in good condition: • Remove dirt with a moist, soft cloth. • Do not put in water. • Do not use aggressive detergents or solutions. Disable the Meter If damaged, do not use and disable the Meter. To disable, remove the batteries. See page 6 for more information. 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
Laser Distance Meter
Memory (419D/424D)
29
6.
Make sure that the Meter is perpendicular to the wall.
7.
Push
to trigger the bottom target (3)
measurement.
The result is the partial vertical distance between
target 1 and target 2. The third measurement shows
in the secondary line.
As an option, use the tracking mode on one or more
targets. To use tracking mode:
1.
Push and hold
for 2 seconds to start tracking
mode.
2.
Move the laser side to side and up and down on the
ideal horizontal target point.
3.
Push
to stop the tracking mode.
Memory (419D/424D)
You can recall a previous measurement from memory, for
example, the height of a room. The Meter stores a
maximum of 20 displays.
To recall:
1.
Push
1x.
2.
Push
and
to move through the stored
displays.
and the memory ID show on the display.
3.
Push
for 2 seconds to use the value shown in
the Summary line for further calculations.
To delete:
1.
Push
and
at the same time.
The Meter deletes all the stored values in memory.
Maintenance
Maintenance and calibration is not necessary for the
Meter. To keep the Meter in good condition:
•
Remove dirt with a moist, soft cloth.
•
Do not put in water.
•
Do not use aggressive detergents or solutions.
Disable the Meter
If damaged, do not use and disable the Meter. To disable,
remove the batteries. See page 6 for more information.